background image

 

23 

Guide for building-in

 

Warning:  Contact  your  local  municipality  for  any  building  codes  regulating  the  installation  of 
outdoor  barbecue  appliances.  Outdoor  installations  must  conform  to  local  codes  or,  in  the 
absence of local codes, with AS5601 - Gas Installations.   
THE CONSTRUCTION OF THE ENCLOSURE AND INSTALLATION OF THE BBQ SHOULD BE CARRIED 
OUT ONLY BY AUTHORISED PERSONS. 
The BBQ must be placed on a construction made from non-combustible materials which must 
support the full weight of the BBQ. 
For Propane installations, the BBQ must be separated from the LPG cylinder and there must be 
enough room so that the cylinder can stand upright. 

THE  BARBECUE  MUST  ALSO  BE  SECURED  TO  THE  ENCLOSURE  TO  PREVENT  IT  BEING  PULLED 
OUT AND STRAINING THE GAS CONNECTIONS. 

 

Ventilation 

Ventilation  must  be  in  accordance  with  AS5601  - 

Gas  Installations. 

In  general,  the  appliance 

should  have  adequate  ventilation  for  complete  combustion  of  gas,  proper  flueing  and  to 
maintain  temperatures  of  immediate  surroundings  within  safe  limits.

    The  air  that  the  BBQ 

requires for proper combustion enters through both sides of the BBQ. The construction of the enclosure 

must provide an unobstructed air supply via a minimum of 260cm2 on both sides.   

       

 

Содержание EA120BIS



























Отзывы: