Cleaning the Dust Container
To achieve the best performance, empty the dust container after each use.
Fig. 6
1. Pull the dust
container straight
out from the side.
(Fig. 6)
2. Empty dust
container contents.
(Fig. 7) If desired-
you may rinse with
water to clean the
dust container –
but
dry thoroughly
before replacing on
the sweeper.
Fig. 7
3. Replace dust container on cordless
sweeper.
4. Periodically remove the brush cover on
the front of the cordless sweeper and
remove any build up of lint, hair or fiber
on the rotating brush. To remove the
cover - grip the cover from the bottom,
pull out and
upward until the
cover unlocks
from the side
slots and tabs
located on the
top of the
sweeper. (Fig. 8)
Fig. 8
2. When first started, the sweeper will start in the highest speed to prevent
overloading the unit when starting on heavy carpets. Other speeds can then be
selected by depressing the speed selector switch.
3. For best cleaning performance, use low speed on hard surfaces, medium speed
on low carpets/rugs, and use high speed on deeper carpets. These are guide
lines and you will find the optimum speed settings for your surfaces and debris to
be picked up through use and experience.
4. The sweeper will automatically try to maintain speeds on all surfaces. The unit
may appear to be pulsing during use to maintain it’s speed, this is normal. If this
occurs, please select the next highest speed to gain optimum performance.
5. To protect your sweeper and it’s components, the sweeper is provided with an
electronic overload circuit. If something were to jam or overload the brush bar
system, the units speed indicators will flash and the unit will stop operating, this
is normal. To reset the unit, remove the tangled object and then depress the
on/off switch once and then depress it again to restart the unit.
NOTE:
If, when you place the sweeper to recharge and the charging indicator
light does
NOT
illuminate, then press the On/Off button once to turn the
sweeper off. The charging indicator light should now light up.
CAUTION:
Do not accidentally turn unit on while cleaning. Do not clean
while unit is charging.
1.
Connect the charger plug to the charging jack or hole on the back of the
sweeper. Plug the the charging adapter into the wall outlet. (120V., 60Hz.) Use only
Charger AD-1215-U8. (Fig. 9)
2.
This cordless sweeper is powered by Ni-Cd batteries. Before first use, they must be
charged for a minimum of 20 hours.
3.
When recharging the unit, the "On/Off" switch
must be in the "OFF" position.
4.
The charging light indicator on the top of the
sweeper will turn solid green to indicate that the
sweeper is properly charging.
5.
To recharge, repeat step #1 above. Charging
times will vary depending upon the amount
of usage between charging cycles.
Charging the Cordless Sweeper
Fig. 9
CAUTION
•
Use only with the battery pack supplied with the unit. (Item # XB617U)
•
Do not attempt to remove the battery pack from the unit to charge it.
•
Never attempt to throw the battery pack or unit into a fire or incinerate it.
•
Do not attempt to remove or damage the battery casing.
•
Battery must be recycled or disposed of in accordance with local
regulations at the end of it's service life. Please consult your Yellow Pages
or local recycling center for more information.
NOTE:
Peak performance may only be realized after the unit has been
charged and discharged two (2) or three (3) times.
IMPORTANT:
To maintain peak performance of your cordless sweeper, it is
recommended that the unit be fully discharged, then
completely re-charged once a month.
Note:
Your sweeper is highly advanced and has electronic controls that optimize the
cleaning ability and durability of the sweeper. Please review the following instructions
carefully to ensure that all features are utilized for best performance.
STORING THE CORDLESS SWEEPER
1.
When running the unit, the battery indicator will start as solid green, change to solid
red when approximately 70% of the battery life is used, and flash red when
in need of charging. The sweeper will prevent the batteries from being deeply
discharged and will indicate this by the speed indicators flashing and the sweeper
will stop operating. This is normal and all that needs to be done is to recharge the
sweeper fully. The speed indicator lights will stop flashing only after the “On/Off”
switch is set to the “Off” position. When recharging from being fully discharged, the
unit must charge for 1 hour minimum before it’s electronics will allow the unit to
operate again.
Your cordless sweeper may be stored by using the slot on the back of the upper
handle and hanging it from a screw secured to a wall or other vertical surface. Use
a #6 flat or pan head screw with the appropriate hardware for the surface that the
sweeper will be mounted on, (i.e. gyproc). Allow the screw head to extend a
approximately 3/16" from the mounting surface. Always empty your sweeper before
hanging up for storage. NOTE: Always empty the sweeper dust cup before storing.
5
6
