background image

GETTING TO KNOW  YOUR SHARK STEAM BLASTER 

cont.

OPERATING INSTRUCTIONS

PREPARATION FOR USE

WARNING:

ALWAYS unplug the appliance prior to any type 

of maintenance on the unit. As all the appliances are 

thoroughly tested before sale, there may be some residual 

water in the boiler.

ASSEMBLY & OPERATION

To connect the tube and the accessories (fig. 1), insert part 

(A) in part (B) turning this slightly to facilitate insertion. Make 

sure that key (C) is securely fastened in the hole provided (D).

Open the reservoir cover (1) and pour in 3 1/4 cups 

(.8 liters) of tap water or distilled water if your tap water is

particularly hard. 

Never add cleaning fluids. 

Close the 

reservoir cover (1). Before plugging in the appliance, make 

sure that you have assembled the tubes and accessories 

correctly and the steam switch on handgrip is “Off”. Press the 

on/off switch (2) to “On”; the steam ready light (3) will come 

on; when the light (3) switches off (after about 1 minute), you 

can start to use the appliance. To spray steam, simply press 

the steam switch button on the handle (6) (fig. 2).
When there is no more steam, fill the tank again. To avoid 

damage, never use the steam gun without water. If the tank is 

full and no steam is sprayed, have the appliance checked by 

the manufacturer.  Always switch off the appliance after use, 

pull out the plug and drain any residual water from water tank.

NOZZLE CLEANING INSTRUCTIONS

Your steamer should not normally require cleaning, however,

should you notice a marked decrease in steam output it may

be necessary to remove mineral deposit build-up from the

nozzle orifice.  First ensure that there is water in the tank. 

If tank is empty, fill with water, (we recommend using purified 

or mineral water), then re-start unit noting whether steam 

output is normal.  If steam output is still low, follow  these cleaning instructions:

1. Unplug steam cleaner from wall outlet.

2. Use a small diameter stiff metal wire such as a straightened metal paperclip 

and carefully insert the end of the wire into the nozzle orifice.

3. Move wire back and forth several times to remove  any deposits.

4. Reconnect appliance to power outlet, switch on and note steam output.

5. If steam performance does not improve, repeat steps #1 through #4.

This appliance cleans many types of hard surfaces with the force of steam without any 

need for chemical cleaning products Obviously, it is also the ideal solution in particular 

situations such as removing wall-paper, washing windows and degreasing many hard 

surfaces in and around the home.

IMPORTANT INFORMATION

Before using the appliance make sure that the materials or the surfaces to be 

cleaned can withstand a temperature of 212° F (100ºC). The steamer is 

equipped with a safety device that, in the case of a fault, vents the steam 
from the bottom of the appliance.

6

1

2

4

5

3

Important User Information

Please note that this steam cleaner has a “

flow through 

injection

” type boiler and is 

not

a pressurized system. It 

will take approximately 45-90 seconds for the steam 

injector to heat up and the “

steam ready light

” to go off. 

Once the steam ready light has gone off, push the steam 

switch on the handgrip to the “On” position (I) in order to 

start the steam flow. Steam power will steadily increase 

during the first four (4) minutes of use, after which time 

steam output will stabilize. Some steam will 

condense

around the floor brush when in use and will cause hard 

surfaces to become wet during the cleaning process, 

this 

is normal.

STANDARD ACCESSORIES

1. THE 

HOSE

includes the steam switch (6) (see page 6) on the handle. 

All the accessories clip onto this and can be removed by pressing the lock key.

2.

THE EXTENSIONS (2)

are connected to each other and to the handle of the 

hose. They extend the range of action and reach of the appliance and assure a 

more comfortable working position. 

3.

THE BRUSH

provided is the ideal accessory for cleaning hardwood, vinyl, tile 

and marble floors. Two clamps are provided to fasten the cloth towels to the 

brush.

4.

THE CONCENTRATOR

makes it possible to clean in even the tightest corners 

(toilet, taps, joints between tiles); the concentrated jet of steam is able to 

remove stubborn, ingrained dirt. 

5.

THE DETAIL BRUSH

is combined with the concentrator by inserting 

over the tip of the concentrator.

6.

THE WINDOW SQUEEGEE

has two rubber edges, a scrubber edge and 

wiping edge, for cleaning windows and mirrors.  When cleaning outside 

windows, always avoid any sudden changes in temperature to prevent 

breakage or cracks.

FOR CONSTANT EFFICIENCY OF THE APPLIANCE, REMEMBER TO 

CLEAN ALL ACCESSORIES AND THE STEAM SUPPLY NOZZLES 

REGULARLY

4

5

Отзывы: