OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Fig. 5
Manual
Suction
Control
NOTE:
Always remove the power plug
from the wall outlet before assembling or
removing accessories and/or filling or
emptying the water tank.
1. Add 5 cups, (40 oz) of water to the tank.
2. Insert plug into electrical outlet.
3. To connect the flexible hose into the air
intake duct, align the tabs on thehose
with the notches on the air intake duct.
Push in firmly and turn 90° clockwise to
lock the hose in place. (Fig. 2)
4. Attach the flexible hose to one or both
extension tubes. (Fig. 2)
Air intake
duct
Flexible Hose
Fig. 2
Using Your Water Filtration
Vacuum For Dry Vacuuming
To Use the Dry Vac Feature
:
8. Attach the wider end of one of the
extension tubes to the flexible hose
handle.
9. Attach the other extension tube to
the first one and ensure a tight
connection.
10. Attach the desired accessory to the
narrow end of the extension tube.
11. When finished using the unit,
unplug from electrical outlet and
empty the water from the unit.
Accessories for Use With the Dry
Vac Feature:
•
Air Driven Turbo Brush
•
Dusting Brush
•
Crevice Tool
•
Floor to Carpet Brush
Fig. 4
Water Tube
Fig. 3
Using The Accessories For Dry
Vacuuming
Dusting Brush
The dusting brush is used
for the furniture, venetian
blinds, books, lamp shades
and shelves.
NOTE: Do not
use the dusting
brush with wet pick-up.
Crevice Tool
For hard to reach areas use crevice
tool with the extension tube or
directly onto flexible hose.
5. To attach the extension tubes, slide the
narrow end of one tube into the wider
end of the other. (Fig. 3)
The casters for the base on your new
Water Filtration Vacuum are packed and
shipped unassembled.
To assemble the
caster to the base,
simply insert the
caster stem into one
of the four (4) holes in
the base and push downward
with the palm of your hand. (Fig. 1)
Repeat for the next three (3) casters.
Fig. 1
IMPORTANT: DO NOT
operate this
vacuum when water level is below the
water tube opening. (Fig. 4)
Assembling the Base Casters
5. Let the foam inlet filter
air dry completely
before replacing in vacuum.
Do not
use a washing
machine to rinse the filter.
Do not use a hair dryer to dry it. Air dry
only. Never operate the vacuum without
the foam inlet filter in place.
6. The water tube may become clogged
with debris. Turn until loose then pull
from removable cover and rinse under
lukewarm water and replace. (Fig. 12)
Fig. 12
Water Tube
Water Tube
Motor Thermostat
Cover
Removable
Cover
Fig. 11
Foam Inlet
Filter
Inlet
Plate
Guide
Rails
Water Tube
Canister
IMPORTANT:
This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
•
Push the On/Off button once.
•
Disconnect the plug from the power
source.
•
Check the source of overheating
problem. (i.e. clogged hose or filter).
•
If clogged hose or filter is found,
unclog the hose and replace the
filters.
•
Wait at least 45 minutes before
attempting to reuse the vacuum.
•
After unit has cooled down for 45
minutes, plug in the cleaner and
push the On/Off button. The vacuum
should start again.
•
If the vacuum still does not start,
contact customer service at:
1 (800) 798-8398.
7. To replace removable cover, slide the
inlet plate into the guide rails inside the
canister.
3. Lift the handle to remove the
removable cover. (Fig. 11) Empty the
water tank into a toilet or an outside
drain.
4. Carefully remove the foam
inlet filter. The foam inlet
filter should be cleaned
regularly depending on
amount of usage. A severely soiled or
clogged filter should be thoroughly
washed with fresh tepid water. A mild
detergent may be used if required.
Cleaning the Flexible Hose
When using the flexible hose for picking up
liquids or other soft foods such as baby
foods or ketchup, always rinse the flexible
hose with warm water after each use before
the dirt hardens on the inside of the flexible
hose.
1. Empty the water tank of all accumulated
water and dirt.
2. Reattach the flexible hose to the
canister.
3. In a pail, pour 5 cups of warm water.
4. Turn the unit “On” and insert the flexible
hose into the pail to suck up the water.
This will rinse out the inside of the
flexible hose.
5. Once you have finished, empty the
water tank again and store your unit
away.
6. Press the "On/Off" Switch to the "On"
position.
7. The flexible hose is equipped with a
manual suction control to adjust the
amount of suction required. For strong
suction ensure that suction button is
closed. To decrease amount of
suction, slide the button to open until
desired strength is obtained. (Fig. 5)
WARNING:
Water level
MUST NEVER
exceed the "Max" level indicated on the
water tank. Empty tank when water level
reaches "
MAX
" indicator. If water is seen
to be coming from the exhaust -
immediately turn the unit off and unplug
from electrical outlet. Empty water tank
and clean. Refill water tank with 5 cups
(40 oz.) of clean water then plug unit
back in and continue working.
NOTE:
DO NOT IMERSE THE
ELECTRICAL PART OF THE VACUUM
INTO WATER OR ANY OTHER LIQUID.
6
3
Содержание CW250H
Страница 2: ......
