manualshive.com logo in svg

Eumetsat Ayecka SR1, Руководство по установке, Страница: 22 / 36

Поделиться
Скачать
Eumetsat Ayecka SR1 Скачать руководство пользователя страница 22

EUM/OPS/MAN/13/730927 

v3F e-signed, 15 April 2016 

Ayecka SR1 DVB Receiver EUMETCast Setup Guide 

 

 

Page 22 of 36 

 

1)

 

Select “

4. System

” 

 

 

================================================================== 
SR1c Serial No. 111700  30AAC                              Run Time:    2:38:47 
Software Version  1.05b232   Hardware Version  2.00  Firmware Version  2.02b922 
 
RX1: Active, Not Locked 
 EUMETCast DVB-S2 1512.500 MHz, Auto 
 
RX2: Not Active, Not Locked 
 Profile 1 1100.000 MHz, Auto 
================================================================== 
 
1. Configuration 
2. Status 
3. Network 

4. System 

5. Statistics 
6. ACM Client 
 
> 4 
4 
 
System 
====== 
1. Warm Reset 
2. Cold Reset 
3. Restore Factory Defaults and Reset 
4. Telnet 
5. NTP Server IP Address                0.0.0.0 
6. SNMP Trap Server IP Address          0.0.0.0 
7. SNMP Read Community                  public 
8. SNMP Write Community                 private 
9. Events Configuration 

A. Software Upgrade 

B. FPGA Image Upgrade 
C. Hardware Information 
D. Menu Timeout                         30 seconds 
E. Factory Settings 
F. Bootloader Upgrade 
G. RX Link Margin Thresholds

 

2)

 

Select “

A. Software Upgrade

” 

> a 
A 
 
Software Upgrade 
================ 
 

1. TFTP Server IP Address

       0.0.0.0 

2. Filename 

3. Show installed versions 
4. Start the download procedure

 

3)

 

Select “3.

 Show installed versions”

 

> 3 

 
Software Versions 
================= 
Index           Version         Image Size      Valid           Active 
1               1.05b238        336140          Yes             Yes 
2               1.05b255        336832          Yes             No 

 

4)

 

Select the latest Software Version, in this case (2) 

 
 
 

 

Содержание Ayecka SR1





































Отзывы:

Нет отзывов