EUCHNER CTP-I.-AS Скачать руководство пользователя страница 9

Страница: 9 / 28

2543028-02-01/21 (Translation of the original operating instructions)

Operating Instructions

Transponder-Coded Safety Switch CTP-I.-AS

7. Manual release

Some situations require the guard locking to be released manually (e.g. malfunctions or an emergency). A function test must

be performed after release.
More information on this topic can be found in the standard EN ISO 14119:2013, section 5.7.5.1. The device can feature

the following release functions:

7.1.

Auxiliary release and auxiliary key release

In the event of malfunctions, the guard locking can be released with the auxiliary release or the auxiliary key release irre-

spective of the state of the solenoid.
Open the guard and close it again after resetting the auxiliary release or auxiliary key release. The device will then operate

normally again.

Important!

The actuator must not be under tensile stress during manual release.

After use, reset the auxiliary release and screw in and seal the locking screw (e.g. with sealing

lacquer).

The auxiliary key release must not be used to lock the switch during servicing to prevent activation

of guard locking, for example.

Loss of the release function due to mounting errors or damage during mounting.

Check the release function every time after mounting.

Please observe the notes on any enclosed data sheets.

7.1.1. Actuating auxiliary release

1. Unscrew locking screw.
2. Using a screwdriver, turn the auxiliary release to in the direction of the arrow.

Guard locking is released.

Auxiliary re-

lease

Locking screw

Содержание CTP-I.-AS





























Результаты поиска

Содержание CTP-I.-AS

Отзывы:

Бренды по названию

Популярные бренды

EUCHNER CTP-I.-AS, Руководство по эксплуатации

Результаты поиска

Содержание CTP-I.-AS

Отзывы:

Бренды по названию

Популярные бренды