ETS-Lindgren HI-3627 Скачать руководство пользователя страница 6

 

Introduction

 

ets-lindgren.com 

 

Notes, Cautions, and Warnings 

 

Note:

 Denotes helpful information intended to provide tips for better 

use of the product. 

 

Caution: Denotes a hazard. Failure to follow instructions 
could result in minor personal injury and/or property 
damage. Included text gives proper procedures. 

 

Warning: Denotes a hazard. Failure to follow instructions 
could result in SEVERE personal injury and/or property 
damage. Included text gives proper procedures. 

 

Note: 

See the ETS-Lindgren 

Product Information Bulletin

 for safety, 

regulatory, and other product marking information. 

Safety Information 

 

Refer to Manual: When product is marked with this 
symbol, see the instruction manual for additional 
information. If the instruction manual has been misplaced, 
download it from 

www.ets-lindgren.com

, or contact 

ETS-Lindgren Customer Service. 

 

High Voltage: Indicates presence of hazardous voltage. 
Unsafe practice could result in severe personal injury or 
death. 

 

High Voltage: Indicates presence of hazardous voltage. 
Unsafe practice could result in severe personal injury or 
death. 

Содержание HI-3627








































Отзывы: