PACKAGE CONTENTS
Part
Description Quantity
A Fixture
1
B
Electrical Box
1
C
Hole Template
1
D
NM Cable Fitting
2
NOTE
:
Keep your receipt and these instructions for proof of purchase.
WARNING
:
RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove
the fuse or turn off the circuit breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
NOTE
:
Select a suitable location that can support the weight of the fixture. Determine the method for mounting the
fixture before installing, based on the type of ceiling.
A
INSTALLATION
Part # DLLP-3IN-550LM-9-5CP-TD / Model # 53840101 can be installed into an opening that is between 3 1/8” and
3 1/2” in diameter, 3 3/8” is recommended.
Part # DLLP-4IN-650LM-9-5CP-TD / Model # 53808103 can be installed into holes cut in the drywall that are between 4
1/8” and 4 3/4”, 4 1/4” is suggested.
Part # DLLP-6IN-900LM-9-5CP-TD / Model 53807103 can be installed into an opening that is between 6” and 6 3/4”,
6 1/4” is recommended.
Shut off power at the electrical panel before beginning the installation.
If installing the fixture in a preexisting hole: Remove existing can and fixture and set aside to recycle in
accordance with local requirements. Measure the ceiling hole to make sure it is the correct size for the fixture.
If installing the fixture in a new location: Trace the hole template (C) in the desired ceiling location and use a hole
saw to cut out the hole.
NOTE
:
1/2"or 5/8" drywall recommended for easy installation.
Installing contractor responsible for ensuring required CCT is selected during installation.
NOTICE
:
The factory setting for the correlated color temperature (CCT) is 2700K, which is the warmest white light.
WARNING:
Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or
other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. • Risk
of fire or electric shock. Installation of this LED Downlight requires a person familiar with the construction and operation of the light fixture’s/luminaire’s electrical system and the
hazard involved. If not qualified, do not attempt installation. Contact a qualified electrician. • Do not make or alter any open holes in an enclosure of wiring or electrical components
during kit installation. • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
NOTICE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • Not for emergency lighting.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
Open electrical box cover.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
A
Spring Clip
USE AND CARE GUIDE
LOWPRO RECESSED DOWNLIGHT WITH COLOR PREFERENCE
®
Model # 53840101
53808103
53807103
Part # DLLP-3IN-550LM-9-5CP-TD
DLLP-4IN-650LM-9-5CP-TD
DLLP-6IN-900LM-9-5CP-TD
Certification # 53840101
53808103-A
53807103-A
B
C
D
1
2
3
4
5
Punch out 1 of the knock out holes.
6
7-A: Feed the conduit (not included) and run the wires based
on local electrical code.
7-B: Snap the supplied NM cable fitting into the knockout if
flexible electrical cable is to be used. Installing contractor is
responsible to follow local electrical code for required wire
entry and installation.
7
Make the electrical connections by inserting the
respective wire into the wire connector:
• Black wire to black wire.
• White wire to white wire.
• Green wire to ground wire.
Tuck wires inside the electrical box.
Close the electrical box cover.
8
Insert the electrical box into the opening in the
ceiling. Connect the connector cable from the
electrical box to the connector cable from the
fixture.
9
Compress the spring clips and insert the fixture into the
opening in the ceiling.
Restore power at the electrical panel.
Turn on the light switch to activate the fixture.
10
Wire Connector
B
B
Connector
Cable
A
Knock Out
Hole
B
A
：
GND
L
N
B
：
D
A
：
B
：
