Etesia AK88 Скачать руководство пользователя страница 17

17

- Particular care should be taken when performing U-turns on sloping 

ground. Prepare for the change of direction and reduce speed so as 

not to lose control of the ride-on brush-cutter.

- Apply the parking brake as soon as the ride-on brush-cutter stops.

- The control of the ride-on brush-cutter skidding along a slope is not 

recoverable by acting on the parking brake pedal.

• The main reasons for loss of control are :

- Insufficient wheels adherence

- Too high speed drive

- Unadapted braking

- Machine not meeting job requirements

An insufficient knowledge of the affects of the ground state, in par

-

ticuliar in slopes

- An incorrect high and a bad load repartition

WARNING ! 

Lift this machine by using a lift table able to 

support the weight of it (see technical specification).

7•1 ENGINE MAINTENANCE

Before carrying out any maintenance, stop the engine, and 

remove the ignition key.

Never touch the exhaust pipe, the cooling cylinder or fins, to 

avoid the risk of burns.

7•1•1 CHECKING THE OIL LEVEL

• To check each time before each use, when the engine is still cold.

• Put the ride-on brush cutter on a flat surface.

• Clean the area around the filter neck to prevent dirt from entering 

the sump.

• Remove the dipstick (a picture 9).

• Wipe the gauge with a clean cloth and place it back in the filler tube.

• Put back the cap so that it bears on the tube but do not screw it down.

• Pull out the dipstick to check the level: the oil level on the gauge must 

be between the [ADD] and [FULL] marks.

• Screw the dipstick back in securely.

7•1•2 DRAINING THE ENGINE OIL

• After the initial servicing at 15 hours, to be performed by your ETE-

SIA dealer, the engine oil must be changed at the first of the fol

-

lowing occasions: every 50 hours (AK88), every 100 hours (AK95, 

AK98, AK98X) or once each year.

• 

Change the oil when the engine is still hot to obtain better outflow of 

oil than when cold.

• Position the machine on a flat surface.

• Stop the engine, and remove the ignition key.

• Place a suitable recipient at the oil drain outlet.

• Unscrew the drain plug (c picture 9) and drain the used oil into a 

container.

WARNING !

 Special care should be taken when draining 

hot oil. Wear gloves.

• Close again the drain plug.

• Clean the perimeter of the filler hole to prevent impurities from get

-

ting into the housing.

• Remove the oil gauge and slowly pour in 10W40 multigrade oil, 

specification API-SL or ACEA-A3 P/N ETESIA 38383 (2 liters) or 

an SAE30 monograde oil through the filler pipe.

• Wipe the gauge with a clean cloth and place it back in the filler tube.

• Rest the plug on the tube without screwing it down.

• Check the oil level using the dipstick. The level should reach but not 

exceed the [FULL] marker.

• Screw the plug down.

• Dispose of used oil at an approved collection point.

7•1•3 CHANGING THE OIL FILTER  

(B PICTURE 9)

• Change the oil filter after 100 hours (AK88) or 200 hours (AK95, 

AK98, AK98X) of operation or once per season.

WARNING ! 

A hot engine can cause very severe burns. 

Before changing oil filter, wait engine cooling.

• Put a receptacle under filter connection.
• Turn filter (clock sense opposed) and take it off.
• Put a clean oil film on the new oil filter joint.
• Set up the new oil filter (clock sense) until the joint reaches the fitting 

surface then screw the oil filter (3/4 hand turn).

• Check oil level and start the engine about 3 minutes: then stop the 

engine and make sure there is no oil leak at oil filter connection.

• Adjust oil engine oil to compensate the oil level decrease due to oil 

filter content.

To check the oil level, place the cap on the tube without 

screwing it.

6• OPERATING INSTRUCTIONS

  7• MAINTENANCE

Содержание AK88





























Отзывы: