ETC echoflex RCT Скачать руководство пользователя страница 21

Страница: 21 / 21

Page 17

RTC CO

, Temperature and Humidity Sensor Configuration Guide

Agency and Regulatory Statements

Built in an ISO9001 certified facility
FCC Part 15.231 (902 MHz models only)

Contains FCC ID: STM300U
The enclosed device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

(I.) this device may not cause harmful interference and

(ii.) this device must accept any interference received,

including interference that may cause undesired operation.

IC RSS-210 (902 MHz models only)

Contains IC: 5713A-STM300U

CE (868 MHz models only), CE Marking

ARIB STDT108 (928MHz models only)

Complies with the Japanese radio law and is certified according to ARIB

STDT108.
This device should not be modified (otherwise

the granted designation or number will become
invalid)

R 206-000372

Содержание echoflex RCT






















Результаты поиска

Содержание echoflex RCT

Отзывы:

Похожие инструкции для echoflex RCT

Бренды по названию

Популярные бренды

ETC echoflex RCT, Руководство по установке и пусконаладке

Результаты поиска

Содержание echoflex RCT

Отзывы:

Похожие инструкции для echoflex RCT

Бренды по названию

Популярные бренды