background image

ETC Installation Guide

ArcSystem ArcSystem Pro Multi-Cell RDM

Corporate Headquarters Middleton, WI, USA +1 608 831 4116 London, UK +44 (0)20 8896 1000
Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535
Web

etcconnect.com

Support

support.etcconnect.com

Contact

etcconnect.com/contactETC

© 2019 Electronic Theatre Controls, Inc. Trademark and patent info: 

etcconnect.com/ip

Product information and specifications subject to change. ETC intends this document to be provided in its entirety.
7490M2160 Rev B Released 2019-07

Introduction

Congratulations on your purchase of ArcSystem products. ArcSystem is a family of overhead LED
products designed for installations where dimming, light quality, and ease of installation are
absolutely essential. With ArcSystem, you will experience perfectly smooth dimming from 100%
down to absolute zero. ArcSystem luminaires come in a variety of form factors, beam angles, and
color-temperature options, all with high-efficiency optics and an outstanding quality of light ideal for
any application.

This manual provides step-by-step instruction on the installation and RDM configuration of ArcSystem
products. For information on ArcSystem products with ArcMesh wireless control, see the

ArcSystem

Installation Manual

at

etcconnect.com/Products/Lighting-Fixtures/ArcSystem

All ETC manuals are

available for download free of charge at

etcconnect.com

.

Safety

ArcSystem products are intended for professional use only.

Read the entire manual before using this

equipment.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including
the following:

READ AND FOLLOW ALL SAFETY
INSTRUCTIONS

Do not use outdoors.

Do not let power supply cords touch hot surfaces.

Do not mount near gas or electric heaters.

Equipment should be mounted in locations and at heights where it will not readily
be subjected to tampering by unauthorized personnel.

The use of accessory equipment not recommended by the manufacturer may cause
an unsafe condition.

Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS

Содержание ArcSystem ARCP2

























Отзывы: