ETC ArcLamp 150 Systems Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 72

background image

Final Installation and Operation

31

Note:

All ArcLamp Drivers are factory set to provide 100% output level to all

circuits. This allows an electrical contractor to check that all products are properly
installed and wired. During system commissioning, the certified ETC technician will
remove this setting and configure DMX addresses for normal use. During normal use
after commissioning is complete, ArcLamps will light if the DMX Control level is greater
than 0.

Updating the Driver Firmware

When commissioning a system installation, check all ArcSystem drivers and multi-cell luminaires
to ensure that the latest firmware is present. If the firmware is not up to date, upgrade it
following the instructions below for your luminaire type.

Wireless ArcMesh Luminaires

Upgrade luminaire firmware using the ArcSystem Configuration Software. The fixture firmware
file and ArcSystem Configuration Software are available for free at

.

RDM Luminaires

Upgrade luminaire firmware using ETC Concert and ETC UpdaterAtor software before
commissioning is completed. For more information on UpdaterAtor, download the

UpdaterAtor

Software Quick Guide

for free at

.

When commissioning a system installation, check all ArcSystem drivers and multi-cell luminaires
to ensure that the latest firmware is present. If the firmware is not up to date, upgrade it using
ETC Concert and ETC UpdaterAtor software before commissioning is completed. For more
information on UpdaterAtor, download the

UpdaterAtor Software Quick Guide

for free at

ArcLamp with ArcMesh Configuration and Commissioning

Initial system programming of a wireless ArcLamp system requires a USB commissioning tool (ARC-CT)

and existing hardware such as a laptop or desktop computer that is connected to the ArcMesh

network. This programming will be carried out by an ETC certified technician at the time of
system commissioning and training.

The following checklist will be included during the configuration process:

•

patching groups of fixtures to specific DMX channels

•

assigning minimum and maximum dimming levels per group

•

assigning power fail/recovery options per group

ArcLamp RDM Configuration

RDM Values

Manufacturer ID: 0x6574 (Electronic Theatre Controls)

Model IDs

ArcLamp Drivers

Model ID

ArcLamp Driver 150 0x120E

ArcLamp Driver 350 0x120F

ArcLamp Driver 700 0x1210

ArcLamp Emergency Drivers

Model ID

ArcLamp Emergency Driver 150

0x130E

ArcLamp Emergency Driver 350

0x130F

ArcLamp Emergency Driver 700

0x1310

«
...
35
36
37
38
39
...
»

Содержание ArcLamp 150 Systems









































































Отзывы:

Нет отзывов

Похожие инструкции для ArcLamp 150 Systems

Бренд: GE Страницы: 138

Бренд: 3M Страницы: 2

Бренд: C.M.O Страницы: 10

Бренд: Dairyland Страницы: 21

Бренд: Radarcan Страницы: 40

Бренд: B&G Страницы: 3

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: Quincy Страницы: 31

Lyme FIA Sofia 2

Бренд: Quidel Страницы: 49

Бренд: Quest Leisure Products Страницы: 12

Бренд: iGuzzini Страницы: 40

Бренд: ProLights Страницы: 28

Бренд: Ultratune Страницы: 12

Бренд: EzCAP Страницы: 15

Бренд: Kelso Страницы: 21

Бренд: SPT Страницы: 2

XMLT-24ELED-200CA8-1

Бренд: DS Produkte Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды