background image

 

 

Page 7 of 41   

Content 

Preface .......................................................................................................................... 5

 

1 Specification ............................................................................................................. 9

 

1.1 Display ................................................................................................................................... 9

 

1.2 Internal memory ..................................................................................................................... 9

 

1.3 Electrical specification ........................................................................................................... 9

 

1.4 Encoder specification ........................................................................................................... 10

 

2 Installation ............................................................................................................. 11

 

2.1 Annoucements before installation ........................................................................................ 11

 

2.2 Installation space and direction ............................................................................................ 11

 

2.3 Installation environment ...................................................................................................... 11

 

2.4 Installation dimension .......................................................................................................... 12

 

2.5 Installation layout ................................................................................................................. 13

 

2.5.1 Layout of rear panel .................................................................................................... 13

 

2.5.2 Rear panel port description ......................................................................................... 13

 

2.5.3 Overall wiring scheme ................................................................................................ 14

 

2.5.4 Electrical wiring scheme ............................................................................................. 14

 

2.6 Definition of system interface .............................................................................................. 15

 

2.6.1 Definition of power interface ...................................................................................... 15

 

2.6.2 Definition of input interface ........................................................................................ 15

 

2.6.3 Definition of external output interface ........................................................................ 17

 

2.6.4 Definition of encoder interface ................................................................................... 17

 

2.6.5 Definition of communication interface ....................................................................... 18

 

3 Parameter Description of Machine Tool .......................................................... 19

 

3.1 Enter parameter page ........................................................................................................... 19

 

3.2 Parameter specification ........................................................................................................ 21

 

4 Debugging .............................................................................................................. 23

 

4.1 Preparation before debugging .............................................................................................. 23

 

4.2 Debugging procedure ........................................................................................................... 23

 

4.3 Debugging ............................................................................................................................ 23

 

4.4 Actual processing ................................................................................................................. 25

 

5 Diagnosis ................................................................................................................ 26

 

Содержание E21S










































Отзывы: