Estate EGD4100SQ Скачать руководство пользователя страница 7

7

Venting Requirements

WARNING: 

To reduce the risk of fire, this dryer MUST BE 

EXHAUSTED OUTDOORS.

4" (10.2 cm) heavy metal exhaust vent and clamps must be used. 
DURASAFE™ venting products are recommended.
DURASAFE™ vent products can be purchased from your dealer 
or by calling Whirlpool Parts and Accessories. For more 
information, see the “Assistance or Service” section of your 
“Dryer User Instructions.”

The dryer exhaust must not be connected into any gas vent, 
chimney, wall, ceiling, or a concealed space of a building.

Do not use an exhaust hood with a magnetic latch.

Do not install flexible metal vent in enclosed walls, ceilings or 
floors.

Use clamps to seal all joints. Exhaust vent must not be 
connected or secured with screws or other fastening devices 
which extend into the interior of the duct. Do not use duct 
tape.

IMPORTANT: Observe all governing codes and ordinances.

Use a heavy metal vent. Do not use plastic or metal foil vent.
Rigid metal vent is recommended to prevent crushing and kinking.
Flexible metal vent must be fully extended and supported when 
the dryer is in its final position. Remove excess flexible metal vent 
to avoid sagging and kinking that may result in reduced airflow 
and poor performance.

An exhaust hood should cap the vent to prevent rodents and 
insects from entering the home.
Exhaust hood must be at least 12" (30.5 cm) from the ground or 
any object that may be in the path of the exhaust (such as flowers, 
rocks or bushes, etc.).
If using an existing vent system, clean lint from the entire length of 
the system and make sure exhaust hood is not plugged with lint. 
Replace any plastic or metal foil vent with rigid metal or flexible 
metal vent.

Plan Vent System

Typical exhaust installations

Typical installations vent the dryer from the rear of the dryer. 

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death
or fire.

A. Dryer
B. Elbow

C. Wall
D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal vent

G. Vent length necessary to connect 

elbows

H. Exhaust outlet

Improper venting can cause moisture and lint to collect 
indoors, which may result in:

Moisture damage to woodwork, furniture, paint, 

Housecleaning problems and health problems.

  wallpaper, carpets, etc.

A

B

B

C

D

E

F

G

H

Содержание EGD4100SQ













Отзывы: