background image

24

Other Useful Information

Cleaning and care

WARNING!

Clean the e-bike properly and maintain it in good working condition. The 

warranty will not apply in case of corrosion due to lack of maintenance.

•  After every ride

, wash your bike with soapy water (liquid dish soap is 

recommended for its ability to remove grease without damaging the bike), 
but do not wash any electrical parts. 

Avoid using high-pressure washers.

 

Always dry your bike with a soft cloth in order to avoid rust and corrosion. While 
carefully drying your entire bike, you will also be able to inspect all the different 
parts and detect any potential problems.

•  Lubrication is an important part of maintenance of electric vehicles. The 

front axle, middle axle flywheel, front fork shock absorber pivot and other 
components should be scrubbed with an appropriate lubricating oil 

every six 

months

.

•  Check the chain tension 

after every ride

. The correct chain tension is 8036N. 

The bike has a freewheel, so you can check the chain tension by spinning the 
pedals backwards. The chain needs to be as tight as possible without creating 
friction that will waste energy and wear the chain and cogs prematurely.

Professional bike mechanics are required to carry out the following steps:
•  To adjust the rear wheel's position, loosen one side and push the rim between 

the chain stays to one side to move the loose end of the axle a short distance 
back or forward. Retighten the nut. Loosen the other side and ease the rim in 
the other direction so the rear wheel is once again straight in the frame.

•  Test again and repeat the process, moving the rear wheel a short distance 

forward or back until the tension is in the target zone. You need to test by 
spinning the pedals because neither cogwheel will be a perfect circle so the 
chain tension will vary as the cranks spin. Once the chain tension is acceptable, 
tighten both nuts fully.

•  During the whole process please pay attention to the motor cable, do not 

damage or loosen the cable.

24

AFTER SALES SUPPORT

1300 886 649

[email protected]

AUS

MODEL: ESTC27M    PRODUCT CODE: 704459   04/2021

Содержание 704459





























Отзывы: