Essilor Instruments APH 550 Скачать руководство пользователя страница 68

Страница: 68 / 78

12)

Replace the printer flame harness after unscrewing the fixing screw (long).

13)

At the time of reassembling after replacing 10), 11) and 12) above, be careful about the
place of the screw clamp and the fixing order of the printer flame harness.

14)

Replace the printer cover or the roller unit after unscrewing 2 fixing screws.
Reassemble it as the roller unit to be parallel to the case.

15)

Replace the relay board assy after unscrewing 4 board fixing screws and removing all of
the harnesses connected.

Fixing screw (long)

Earth harness

Washer
tooth lock washer

Printer
unit

Printer case

Wiring direction of
earth unit

Fixing screws (short)

Fixing screw (long)

Printer flame harness

Thermal printer

Printer case

Fixing screws

Roller unit

Printer cover

Fixing screws

Relay board assy

Содержание APH 550















































































Результаты поиска

Содержание APH 550

Отзывы:

Похожие инструкции для APH 550

Бренды по названию

Популярные бренды

Essilor Instruments APH 550, Руководство по обслуживанию

Результаты поиска

Содержание APH 550

Отзывы:

Похожие инструкции для APH 550

Бренды по названию

Популярные бренды