Espressif Systems ESP8266EX Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 48

Espressif Systems ESP8266EX Скачать руководство пользователя страница 26

!

!

!

Espressif Systems

ESP8266EX

Hardware User Guide

Name

Functional Description

Micro USB Interface

There are two USB interfaces, one is used for 5V power supply, the other one is used
for serial communication. (Refer to Part 1 in Fig. 14)

Please pay attention to the notice on Page 25.

Power Supply

One USB interface is used to supply 5V power, while a DC/DC regulator is used
convert 5V to 3.3V, supplying power for WiFi part. There is one indicator light
besides the 3.3V power, and a skip stitch that can be used to test the power current.

Slide Switches

Slide switches are used to convert voltage level of GPIO0 interface and chip enable
pin CH_EN.
It should be noted that when a slide switch is pulled up, the voltage level is high,
while when pulled down, the voltage level is low. (Refer to Part 3, 21, and 22 in Fig.
14)

Reset Buttons

SW1 is connected to MTCK (GPIO13), and is used for resetting IoT applications.
Function of SW2 has not defined yet. (Refer to Part 26 and 14 in Fig. 14)

Indicator lights

Red light (D2) is an indicator light for the working condition of WiFi.

It’s not available now!

Blue light (D3) is an indicator light for the communication of the server. (Refer to Part
27 in Fig. 14)

Green light (D1) is an indicator light for relay switch control. (Refer to Part 7 in Fig. 14)

Blue light (D11) and Red light (D10) indicate working status of Rx and Tx serial ports
respectively. (Refer to Part 2 in Fig. 14)

Red light (D12) is indicator light for 5V power supply. (Refer to Part 3 in Fig. 14)

Function of D4, D13, D14, and D16 can be defined by users themselves. (Refer to
Part 14 in Fig. 14)

Jumpers

J82: It needs to be short-circuited using a jumper, so that 3.3V power supply can be
connected to other posterior circuits. It can also be used to test the power of the
circuit. (Refer to Part 5 in Fig. 14)
J3: It functions as chip selection for HSPI flash.
HSPI flash is closed when the jumper is short-circuiting connected to the upper two
needles, while HSPI is enabled when the jumper is short-circuiting connected to the
lower two needles. (Refer to Part 19 in Fig. 14)
J14 and J67: When J14 is short-circuiting connected, it indicates that GPIO13 is
connected to U0CTS; when J67 is short-circuiting connected, it indicates that
GPIO15 is connected to U0RTS. (Refer to Part 24 in Fig. 14)
J77: When J77 is short-circuiting connected, is indicates that GPIO16 is connected to
EXT_RSTB. This can be used to awake the device from deep-sleep mode. (Refer to
Part 12 in Fig. 14)

Interfaces

UART, HSPI, SDIO/SPI, I2C, ADC_IN, GPIO16, relay control, PWM, IR TX and RX

Espressif Systems

/

Jun 1, 2015

26 48

«
...
24
25
26
27
28
...
»

Содержание ESP8266EX

















































Отзывы:

Нет отзывов