Eskridge 600 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 9

Eskridge 600 Скачать руководство пользователя страница 4

Model 600 Spindle Drive service manual, SM600LS2-AG Page 3

Eskridge, Inc. Olathe, Ks. 913-782-1238 www.eskridgeinc.com

LUBRICATION & MAINTENANCE

Operating Position

Single stage

Oil Capacity

Double stage

Triple stage

Oil Level

Horizontal Shaft

-

17 qts / 16

Liters

19 qts / 18

Liters

To horizontal centerline of

gear drive

Vertical Shaft (Pinion Up)

-

26 qts / 24

Liters

28 qts / 26

Liters

To side port on gear drive

base

Vertical Shaft (Pinion Down)

29 qts / 27 Liters

32 qts / 30 Liters

To midway on upper/

primary gear set

Using the chart below, determine an appropriate lubricant viscosity. Use only EP (extreme pressure) or API GL-5 designated lubricants.
Change the lubricant after the first 50 hours of operation and at 500 hour intervals thereafter. The gear drive should be partially disas-
sembled to inspect gears and bearings at 1000 hour intervals.

80W90 conventional

75W90 conventional

85W140 conventional

75W90 synthetic

80W140 synthetic

Note: Ambient temperature is the air temperature measured in the immediate vicinity of the gearbox. A Gearbox exposed to the direct rays of
the sun or other radiant heat sources will operate at higher temperatures and therefore must be given special consideration. The max operating
temp must not be exceeded under any circumstances, regardless of ambient temperature.

Recommended ambient and operating temperatures for conventional and synthetic gear lubricants

-50 -25 0 25 50 75 100 125 150 175 200 225 250 F

-45 -32 -18 -4 10 24 38 52 66 79 93 107 121 C

Min Ambient/operating temp

Max Operating temp

Max Ambient temp

ESKRIDGE MODEL

600 OIL CAPACITIES

ESKRIDGE PART NUMBER INTERPRETATION

Note: All standard Eskridge Geardrives are issued a descriptive part number which includes information regarding
the Model, means of shaft retention, base style, shaft style, input mounting, input shaft size, overall ratio and vari-
ous available options. For a detailed breakdown of this information, please refer to Eskridge product specification
sheets found at: http://www.eskridgeinc.com/geardrives/gearprodspecs.html

«
...
2
3
4
5
6
...
»

Содержание 600










Отзывы:

Нет отзывов