manualshive.com logo in svg

ESDEC FLATFIX WAVE, Руководство пользователя, Страница: 17 / 20

Поделиться
Скачать
ESDEC FLATFIX WAVE Скачать руководство пользователя страница 17

  ANNEX D - GROUNDING, BONDING AND LIGHTNING PROTECTION

 

     

                

 

 

 

 

 

 

16

  2 

METHOD OF GROUNDING/BONDING

Grounding

Thanks to the integrated part bonding, no additional bonding between the metal parts is required.

1. The teeth at the top of the high base elements engage in the frame edge of the solar panels.

2. The teeth on the underside of the high base elements engage in the profile of the units.

3. Fully tightening the panel lock ensures correct contact of the panel frame with the high base.

Integrated bonding

• 

The grounding conductor (≥Ø 4mm2) runs parallel to the plus and min. conductors and is connected to a separate grounding point of the 

         inverter.

• 

Connect at least one rail in a field to a ground rail.

• 

Each individual PV field will have its own bonding conductor.

• 

The grounding cable can be fitted with a cable eye and screwed to the rail together with serrated spring washers.

• 

Correct assembly: protected against corrosion and firmly assembled. 

INSTALLATION OF THE BONDING CONDUCTOR

Содержание FLATFIX WAVE





















Отзывы:

Нет отзывов