background image

Front Laser Shifters: The Front Laser 
Shifters (Code letter B on the 

installation manual) can be mounted 
different ways. They can be mounted 
inside the grill area as on the 
Yellow Z06 
with the supplied mount 

brackets and 3M Scotch VHB

 

1

 double 

sided tape (follow surface preparation 
and temperature instructions for the 
VHB tape),  

 
      or 

they 

can 

be 

mounted 

outside the grill using  

 

 

 

 

 

 

VHB double sided tape as shown on the black  

 

 

 

 

 

 

car. Spread the shifters as far apart as possible  

      but 

maintain 

clear 

view of the road ahead. The  

 

 

 

 

 

 

shifters should be mounted as level as possible  

 

 

 

 

 

 

(use the sight line on the short side of the shifter  

 

 

 

 

 

 

as a level line) with the bubble lens on the top of  

      the 

front 

face. 

Remove 

the 

protective 

film 

from 

 

 

 

 

 

 

 

the front face after installation. Feed the wires  

      towards 

the 

passenger 

side 

of 

the 

car 

under 

the 

 

 

 

 

 

 

 

hood. 

 
Front Radar Receiver: The Front Radar Receiver (Code letter A on the installation manual) 
can be mounted inside the grill area using self taping hardware. Place the unit in the middle 
and screw it to the plastic shroud. The unit can also be mounted inside under the hood 

using double side tape and placed on the small ledge on the driver side as along as no 
metallic parts obstruct the view forward (tip: do not mount radar receiver behind license 
plate). The ledge is located behind the bumper.  

 
Penetrating the Firewall: The wires from both front 
shifters and the radar receiver should be run towards 
the passenger side. The main wiring harness going 

into the firewall will have a soft rubber boot around it. 
You will need to disconnect and remove the battery 
except on the Z06.  
 

Take a small sharpened 1/8 inch metal rod and poke three holes through the rubber boot. 
Cut the phone jack connectors off the wires and run thru the holes in the rubber boot

.  

                                                 

1

 3M VHB (Very High Bond) tape 4979F Black, 1 inch x 36 yard 62.0 mil. thick.  Conformable foam, multi-purpose acrylic 

adhesive, black, clear PE film liner, double sided.  VHB tape can be ordered through any automotive paint supple outlet that 

carries 3M automotive products. 

Содержание SRX Corvette C-6








Отзывы: