manualshive.com logo in svg

ESAB Powercut 900, Инструкция по эксплуатации, Страница: 65 / 72

Поделиться
Скачать
ESAB Powercut 900 Скачать руководство пользователя страница 65

65

7.1 general

Always provide the serial number of the unit on which the parts will be used. The serial number is stamped on 

the unit nameplate.

To ensure proper operation, it is recommended that only genuine ESAB parts and products be used with this 

equipment. The use of non-ESAB parts may void your warranty.

Replacement parts may be ordered from your ESAB Distributor.

Be sure to indicate any special shipping instructions when ordering replacement parts.

Refer to the Communications Guide located on the back page of this manual for a list of customer service phone 

numbers.

7.2 Ordering

Bill of material items that have blank part numbers are provided for customer information only.  

Hardware items should be available through local sources.

Note:

7.0  replacement parts

SECTION 7 

rEpLACEMENT pArTS

Model # p/N 

DESCrIpTION

SCHEMATIC DIAgrAM WIrINg DIAgrAM

1

0558008120

PowerCut-900   208/230v

0558008422

0558008423

2

0558008126

PowerCut-900 Mech   208/230v

0558008422

0558008423

3

0558008123

PowerCut-900   230v CE

0558008676

0558008677

4

0558008139

PowerCut-900 Mech   230v CE

0558008676

0558008677

5

0558008127

PowerCut-900   460v

0558008424

0558008425

6

0558008130

PowerCut-900 Mech   460v

0558008424

0558008425

7

0558008131

PowerCut-900   575v BL

0558008426

0558008427

8

0558008140

PowerCut-900 Mech   575v BL

0558008426

0558008427

9

0558008133

PowerCut-900   400v

0558008428

0558008429

10

0558008931

PowerCut-900 Mech   400v

0558008428

0558008429

11

0558008135

PowerCut-900  380-400v CE

0558008428

0558008429

12

0558008138

PowerCut-900 Mech  380-400v CE

0558008428

0558008429

Содержание Powercut 900









































































Отзывы:

Нет отзывов