manualshive.com logo in svg

ESAB Powercut 900, Инструкция по эксплуатации, Страница: 48 / 72

Поделиться
Скачать
ESAB Powercut 900 Скачать руководство пользователя страница 48

48

SECTION 3 

INSTALLATION

3.5.1  Input Voltage Changeover - 208/230 Voltage 60 Hz UNITS ONLY

208 or 230 Mode

The PowerCut 900, 208/230 vac, 60 Hz model, is factory set for 230 vac input. If using 208 vac input, the PowerCut 

900 must be reconnected as follows before connecting to your input power:

1.  Remove cover.

2.  Locate the Output Diode Bridge (D101) (see Figure 3.2A) on the left side towards the front panel. Disconnect 

and exchange the X2 and X3 leads only. Leave other smaller wire in place. For 208 vac input, X2 is connected to 

D101-2 and X3 is connected to D101-3. Ensure the connections are firmly tightened to 22 in/lbs (2.5 Nm).

3.  Locate the J27 Control Supply Voltage jumper plug (violet wire) on left side towards the rear panel (see Figure 

3.2b).   Remove the cover plug from the J23 (208 V) header. Move J27 jumper from J20 (230 V) to J23 (208 V). 

Place the cover plug on the J20 (230 V) header.  

4.  Reinstall cover and connect the PowerCut 900 to 208 vac input power.

ELECTrIC SHOCK CAN KILL! prECAUTIONArY MEASUrES SHOULD 

BE TAKEN TO prOVIDE MAxIMUM prOTECTION AgAINST ELECTrI-

CAL SHOCK. BE SUrE THAT ALL pOWEr IS Off BY OpENINg THE LINE 

(WALL) DISCONNECT SWITCH AND BY UNpLUggINg THE pOWEr 

COrD TO THE UNIT WHEN rECONNECTINg fOr 208 VAC INpUT.

WArNINg

figure 3-2. Original factory Setup for 230 vac Input on

power Source with 208/230 vac, 60 Hz Input power Capability

BR102

figure 3-2b.

208 vac

figure 3-2a.

208 vac

Disconnect and exchange 

the x2 and x3 leads only.

Move J27 jumper 

from: J20 (230 V) 

to: J23 (208 V)

Do not move this lead.

Содержание Powercut 900









































































Отзывы:

Нет отзывов