manualshive.com logo in svg

ESAB Heliarc 161, Инструкция по эксплуатации

Поделиться
Скачать
ESAB Heliarc 161 Скачать руководство пользователя страница 23

23

Unit dead, cooling fans not running, no power “ON”
light

Tungsten is blued and weld sooty & black

HF sparks between tungsten and work but no arc
transfer to workpiece.

Nothing happens when TIG torch switch is
pressed. No gas flows, no HF or power at the tung-
sten

Difficulty in initiating DC TIG arc

Tungsten melts and transfers to weld pool

Main fuse frequently blows

If all else fails

SECTION 5

TROUBLESHOOTING

Fault

Remedy

Check front panel power switch is on. Check main
supply. Check main supply fuse

Check argon shielding gas supply is on and flow
is adequate

Check work lead is properly connected to a clean
location on the workpiece

Check the torch switch is properly connected at
the 14 pin socket. Check the switch and switch
wires.

Check a 2% thoriated,ceriated or lanthanated
tungsten is being used. Check for a good work
lead connection. Test machine in touch start mode
to confirm arc can be established. Regrind tung-
sten tip

Check TIG torch is connected to - (minus) output
socket. If AC TIG welding, reduce setting on bal-
ance control towards more negative polarity
(maximum penetration)  or use a larger tungsten

Welding current level being used causes primary
current to exceed fuse rating. Use a larger fuse,
refer to specification section

Contact your ESAB distributor or an authorized
ESAB Service Center

Содержание Heliarc 161

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды