ESAB AristoMig 4004i Pulse Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 26

background image

4 INSTALLATION

0463 431 001

- 10 -

© ESAB AB 2016

4

INSTALLATION

The installation must be carried out by a professional.

CAUTION!

This product is intended for industrial use. In a domestic environment this product
may cause radio interference. It is the user's responsibility to take adequate
precautions.

4.1

Location

Position the welding power source such way that its cooling air inlets and outlets are not
obstructed.

4.2

Lifting instruction

4.3

Mains supply

NOTE!
Mains supply requirements

This equipment complies with IEC 61000-3-12 provided that the short-circuit
power is greater than or equal to S

scmin

at the interface point between the user's

supply and the public system. It is the responsibility of the installer or user of the
equipment to ensure, by consultation with the distribution network operator if
necessary, that the equipment is connected only to a supply with a short-circuit
power greater than or equal to S

scmin

. Refer to the technical data in the

TECHNICAL DATA chapter.

«
...
8
9
10
11
12
...
»

Содержание AristoMig 4004i Pulse



























Отзывы:

Нет отзывов

Похожие инструкции для AristoMig 4004i Pulse

Бренд: U-Line Страницы: 7

Бренд: jablotron Страницы: 2

Бренд: jablotron Страницы: 24

Бренд: Keller Страницы: 17

Бренд: Uniden Страницы: 32

Бренд: Zip Страницы: 16

Бренд: Velleman Страницы: 18

Norton 1600 Series

Бренд: Assa Abloy Страницы: 6

Бренд: JBL Страницы: 4

Бренд: Salto Страницы: 4

MarCell MAR-A-500

Бренд: Sensored Life Страницы: 2

Бренд: Magnavox Страницы: 23

Бренд: Raychem Страницы: 6

Бренд: INNO Instrument Страницы: 45

Бренд: Urrea Страницы: 16

Бренд: 2VV Страницы: 30

Бренд: Parrot Products Страницы: 8

Бренд: Zepro Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды