background image

www.desatech.com

108796-01M

0

CleanInG and 

maIntenanCe

 WARNING: Installation and 

repair should be done by a quali-

fied service person. The appli-

ance should be inspected before 

each use and at least annually 

by  a  qualified  service  person. 

More frequent cleaning may be 

required  due  to  excessive  lint 

from  carpeting,  bedding  mate-

rial, pet hair, etc. It is imperative 

that the control compartments, 

burners and circulating air sys-

tem be kept clean.

 WARNING: The logs can be 

hot. Handle only when cool.

 WARNING: Turn off gas and 

electrical power before servicing 

appliance.

  WARNING:  Failure  to  keep 

the  primary  air  opening(s)  of 

the burner(s) clean may result in 

sooting and property damage.

PILOT AND BURNER

•  Remove  logs  and  ember  material  before 

cleaning burner and replace when cleaning 
is complete.

•  Burner  and  controls  should  be  cleaned 

with  compressed  air  to  remove  dust,  dirt 
or lint.

•  Use a vacuum cleaner or small, soft bristled 

brush to remove excess dust, dirt or lint.

LOGS

•  If  you  remove  logs  for  cleaning,  refer  to 

log placement information on page 1 to 
properly replace logs.

•  Use  a  vacuum  cleaner  to  remove  any 

carbon buildup on logs.

•  Replace log(s) if broken. See 

Replacement 

Parts

.

•  Replace  ember  material  periodically  as 

needed. See 

Replacement Parts

.

serVICe hInts

When Gas Pressure Is Too Low

•  pilot will not stay lit
•  burner will have delayed ignition

•  fireplace will not produce specified heat

•  propane/LP gas supply may be low if using 

propane/LP gas

If using propane/LP gas, you may feel your 
gas  pressure  is  too  low.  If  so,  contact  your 
local propane/LP gas supplier.

teChnICal serVICe

You may have further questions about instal-
lation,  operation  or  troubleshooting.  If  so, 
contact  DESA’s  Technical  Service  Depart-
ment at 1-866-67-6040. When calling please 
have your model and serial numbers of your 
heater ready.
You can also visit DESA’s Technical Services 
web site at 

www.desatech.com

.

rePlaCement Parts

Note:

 Use only original replacement parts. This 

will protect your warranty coverage for parts 
replaced under warranty. 

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If 
they can’t supply original replacement part(s) 
call DESA’s Technical Service Department at 
1-866-67-6040 for referral information.
When calling DESA, have ready
•  your name
•  your address
•  model  and  serial  numbers  of  your 

fireplace 

•  how fireplace was malfunctioning

•  type of gas used (propane/LP or natural 

gas)

•  purchase date
Usually, we will ask you to return the part to 
the factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If 
they can’t supply original replacement part(s) 
call  DESA  at  1-866-67-6040  for  referral 
information.
When calling DESA, have ready

•  model number of your fireplace 

•  the replacement part number

Содержание M36E

































Отзывы: