manualshive.com logo in svg

ESA 125T, Руководство пользователя

Поделиться
Скачать
ESA 125T Скачать руководство пользователя страница 11

113170-01E 

1
1

 

www.desatech.com

 

 

 

SERVICE PROCEDURES

 

 

WARNING: To avoid risk of 

burn and electrical shock, never 
attempt to service heater while it 
is plugged in, operating or hot.

 

 

UPPER SHELL REMOVAL

 

1.

 

Remove screws along each side of heater using 
phillips screwdriver. These screws attach upper 
and lower shells together. See Figure 7.

 

2.

 

Lift upper shell off.

 

3.

 

Remove fan guard.

 

AIR OUTPUT, AIR INTAKE AND LINT 
FILTERS

 

1.

 

Remove upper shell (see Figure 7).

 

2.

 

Remove filter end cover screws using 5/16" 
nut-driver (see Figure 10).

 

3.

 

Remove filter end cover.

 

4.

 

Replace air output and lint filters.

 

5.

 

Wash or replace air intake filter (see 

Preventa- 

tive Maintenance Schedule

, page 8).

 

6.

 

Replace filter end cover.

 

7.

 

Replace upper shell.

 

IMPORTANT: 

Do not oil filters.

 

Screw

 

2

 

 

Upper Shell

 

Air Intake 
Filter

 

Filter

 

End

 

1 

Cover

 

 

 

Lint Filter

 

 

 
 

FAN

 

 

 

Figure 7 - Upper Shell Removal

 

 

Air Output Filter

 

Figure 10 - Air Output, Air Intake and Lint 

Filters

 

IMPORTANT: 

Remove  fan  from  motor  shaft 

before removing motor from heater. The weight 
of the motor resting on the fan could damage the 
fan pitch (see Figure 8).

 

1.

 

Remove upper shell (see Figure 7).

 

2.

 

Use  1/8"  allen  wrench  to  loosen  setscrew 
which holds fan to motor shaft.

 

3.

 

Slip fan off motor shaft.

 

4.

 

Clean fan using a soft cloth moistened with 
kerosene or solvent.

 

5.

 

Dry fan thoroughly.

 

6.

 

Replace fan on motor shaft. Place fan hub flush 
with end of motor shaft (see Figure 9).

 

7.

 

Place setscrew on flat of shaft. Tighten setscrew 
firmly (40-50 inch-pounds/4.5-5.6 n-m).

 

8.

 

Replace upper shell.

 

 

PUMP PRESSURE ADJUSTMENT

 

1.

 

Remove  fan  guard  using  medium  phillips 
screwdriver.

 

2.

 

Remove pressure gauge plug from filter end 
cover (see Figure 11).

 

3.

 

Install accessory pressure gauge (part number 
HA1180).

 

4.

 

Start  heater  (see 

Operation

,  page  5).  Allow 

motor to reach full speed.

 

 

 

 

Relief 

Valve

 

 

Pressure

 

 

 

Setscrew

 

 

Fan

 

Setscrew

 

Motor

 

 

Fan

 

Gauge 
Plug

 

 

 

Flush

 

Figure 11 - Pressure Gauge Plug 

Removal

 

 

Motor Shaft

 

Figure 8 - Fan, Motor 

Shaft and Setscrew 

Location

 

Motor 
Shaft

 

Figure 9 - Fan 

Cross Section

 

Содержание 125T






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды