background image

 

 

 

 

 

SAFETY 

 

Improper  operation  can  cause  serious 
injury or death. 

Pre-operation  

 

This machine is designed to grade and level dirt.  

NEVER

 use this machine for any other purpose.

 

 

Read  the  operator

’s  manual  for  the  “Skid  Steer 

Loader.

  NEVER

  allow  untrained  people  to 

operate.

 

  Operating instructions must be given to everyone 

before operating this attachment and at least once 
a  year  thereafter  in  accordance  with  OSHA 
regulations. 

 

NEVER

 exceed the maximum recommended input 

power or speed specifications for the attachment. 
Over-powering  or  over-speeding  the  attachment 
may  cause  personal  injury  and/or  machine 
damage.   

 

Keep all shields, guards, and covers in place.

 

 

Do not modify equipment or add attachments that 
are not approved by Erskine Attachments LLC.

 

 

Use adequate safety warning lights and devices as 
required  by  local  regulations.  Obey  all  local  laws 
and  regulations  regarding  machine  operation  on 
public property.

 

Operation

 

 

Hydraulic connections may be hot after use.  Use 
gloves if connecting or disconnecting after use.

 

 

Check  and  be  sure  all  operating  controls  are  in 
neutral before starting the engine.

 

  Always  stay  in  the  operator  position  when  using 

the attachment.   

  Keep  people  away  from  loader  and  attachment 

when in use.  This attachment has moving parts.

 

 

 

Operation (continued)

 

 

NEVER

 operate near embankments or terrain that 

is so steep that rollover could occur.

 

 

Before  leaving  the  operators  position,  lower  the 
attachment to rest flat on the ground, stop engine, 
relieve  hydraulic  pressure  to  the  attachment,  set 
park brake, and wait for all motion to stop.

 

 

NEVER

  place  hands  near  moving  parts  or  clear 

debris while engine is running.

 

Avoid High Pressure Fluids Hazard 

  Escaping  fluid  under  pressure  can 

penetrate  the  skin  causing  serious 
injury. 

  Avoid  the  hazard  by  relieving  the 

pressure 

before 

disconnecting 

hydraulic lines. 

  Use  a  piece  of  paper  or  cardboard,  NOT  BODY 

PARTS,  to  check  for  suspected  leaks.    Wear 
protective  gloves  and  safety  glasses  or  goggles 
when  servicing  or  performing  maintenance  on 
hydraulic systems. 

  If an accident occurs, see a doctor immediately.  

Any fluid injected into the skin must be surgically 
removed  within  a  few  hours  or  gangrene  may 
result.  

Maintenance 

 

NEVER

  make  adjustments,  lubricate,  clean,  or 

perform any service on the machine while it is in 
operation.

 

 

Make sure the attachment is serviced on a daily 
basis.  Improper maintenance can cause serious 
injury  or  death  in  addition  to  damage  to  the 
attachment and/or your equipment.

 

 

 

 

 

Содержание 900320





















Отзывы: