NOTE 2
: The memory capacity is of 21 transmitter keys. This means that a 2 key transmitter
needs 2 memory positions. It is possible to display the memory position by following the
procedure 10.
A transmitter key can be memorized on each relay RR or RV but not on both.
10 - Display of the transmitter memory position
With this procedure it is possible to display the position occupied by a given transmitter key.
1) Push the transmitter key for which you need to know the memory position and verify the
activation of the relay and the led.
2) Push the button
PR
of the receiver for 1 second.
At this point begins a sequence of 7 lightings of the two led LR and LV: by taking a note of what
color light blinks, it is possible to get the memory position, according to the table 1:
Led flash
1
2
3
4
5
6
7
Green LED
1
2
4
8
16 32 64
Red LED
0
0
0
0
0
0
0
Example
:
Transmitter blinks the following seven times after pushing the red relay (PR) key:
RED - RED - GREEN - GREEN - RED - RED - RED
This corresponds to the 12th position.
11 - Overwrite of an already stored Transmitter code
1 - Determine transmitter key memory position ( see paragraph 10 )
2 - Press corresponding relay programming key
PR
or
PV
on receiver for
4 seconds
.
3 - Within 2 seconds press
PV
: the led switches off.
4 - Within 2 seconds enter the transmitter memory position of existing transmitter by using (
PR red
) and (
PV green
) accordingly Tab. 1. There must be a total combination of seven
button pushed ( PV or PR) to match the memory position of existing transmitter.
5 - Within 1 second press the new transmitter key to be programmed.
The previous transmitter key will be removed and replaced by the key pressed in step 5.
12 - Memory capacity display
This procedure allows to display the number of occupied memory positions.
1) Push the button
PV
of the receiver for 1 second.
At this point the receiver begins a sequence of 7 lightings of the leds LR and LV. Referring to that it
is possible to obtain the number of the occupied memory positions, according to tab.1
13 - Memory full
When the receiver memory is full and a memorization procedure is started, both the leds LV and
LR blink 3 times.
14 - Total memory erasure
1) Keep on pushed
PR
of the receiver until the red led LR is turned on.
2) Keep
on pushed simultaneously
PV
and
PR
for
4 sec
. The receiver will give the operation
confirmation with 3 blinks of the leds LV and LR.
15 - Relay configuration display
Keep on pushed
PR (or PV)
of the receiver for 4 sec. The current configuration of the relay is
displayed by the corresponding led, according to table 2 :
16 - Relay programming
The relays can be programmed in all the 3 modes ( pulse, step or delayed), but the following
combinations :
Not allowed configurations
Red relay (RR)
Green Relay (RV)
Step
Delayed
Delayed
Delayed ( with different delay time )
17 - Relay RR (RV) configuration
- (Fig. 4)
The operating mode of the relay is cyclic. See below to change the mode
-If the relay is set as pulse:
it becomes latching and after timed;
-If the relay is set as latching:
it becomes pulse;
-If the relay is set as timed:
it becomes pulse.
Operating mode ( RR or RV )
Pulse mode
Continuous light
Step mode
Slow blinking
Delayed mode
Fast blinking
Led light type (LR or LV)
Fig. 5
1
1
1
PR
PV
PR
PR
PR / PV
PR
18 - Relay RR ( RV) timing settings
-( Fig. 5)
The time settings of the delayed relay can be done only if the relay has been previously set as
pulse.
Push the button
PR
(PV)
of the receiver for
4 sec
.;the led LR (LV) will turn on and will display the
present operating mode of the relay RR (RV). If the led blinks slow or fast push again
PR
for
1
sec.
and the relay will be set as pulse. Then push
PR
for
1 sec.
and the led LR (LV) switches off.
Then, within 2 seconds, begin to set the selected relay time, by pushing on the buttons PR and
PV according to Table 4 and considering that PR has weight of "0" while PV has weight "1".
NOTE
:
The last pressures on PR of the sequence are not necessaries.
Example 1: 8 sec. delay : input the sequence : PR - PR - PR - PV - PR - PR - PR.
Example 2: 2 min delay.: input the sequence : PV - PR - PR - PR - PR - PR - PV.
Fig. 4
1
1
1
PR / PV
PR
Pulse
Step
Delayed
Step
Pulse
Pulse
PR
PR
19 -
Jumper J1 and J2 settings
The jumper J1 and J2 allow to set the operating mode of the receiver when it replies to the
transmitter.
Once received the second signal by the transmitter, the receiver sends back the “Status signal”
to communicate the transmitter the status of the relays or the auxiliary inputs.
The information sent contains the status of the relays ( which can be in step or pulse/delayed
mode ) or the inputs which can be open or closed.
The message is different depending upon the jumper J1 and J2.
Before to send the message, the receiver does a test on the status of the relays RR and RV and
the inputs connected at the terminals 1,2, 3)
With the information received by the receiver, the transmitter switch on the led green or red and
the buzzer. Refer to table 5 to know the status of the relays / inputs by the colour of the led and
the bip of the buzzer.
NOTE :
When the receiver sends the logic level of the auxiliary inputs ( jumper J1, J2 OPEN),
the message is sent to the transmitter with a delay of 4 sec. to allow the security appliances
connected to change their status.The status of the inputs ( I1-C and I2-C ) is monitored by the 2
led L1 and L2.
Logic level of input at terminal 1-3
Logic level of input at terminal 2-3
Status relay RR
Status relay RV
Current configuration
Final configuration
IS-RTWERUK Rev. 3 del 13.06.2017
Manufactured by CDVI Wireless Spa
Via Piave, 23 - 31020
San Pietro di Feletto (TV) - Italy
Tel: +39.0438.450860 - Fax: +39.0438.455628
Web: www.erone.com
T H E S M A R T L I V I N G
The guarantee period of the product is 24 months, beginning from the manufacturer date.
During this period, if the product does not work correctly, due to a defective component, the
product will be repaired or substituted at the discretion of the producer. The guarantee does not
cover the plastic container integrity. After-sale service is supplied at the producer's factory.
GUARANTEE
Tab 4
Pressioni tasti / Button act /
Tastenbetatingung/
1° 2° 3° 4° 5° 6° 7°
Presion botones
sec/sec./sek/seg. 1 2 4 8 16 R R
sec/sec./sek/seg. 10 20 40 80 160 V R
Min/min/min/min 2 4 8 16 32 R V
Min/min/min/min
20 40 80 160 320 V V
Tab. 1
Tab. 2
Tab. 3
J1
J2
Jumper
Open
Jumper
Closed
OPEN
CLOSED
BUZZER TX
LED TX
1 BEEP
2 BEEP
RED
GREEN
OPEN
CLOSED
BUZZER TX
LED TX
1 BEEP
2 BEEP
RED
GREEN
PULSE
STEP
BUZZER TX
LED TX
2 BEEP
2
( on )
BEEP
GREEN
GREEN
BUZZER TX
LED TX
2 BEEP
2
( on )
BEEP
GREEN
GREEN
Tab. 5
PULSE
STEP
1
( off )
BEEP
RED
1
( off )
BEEP
RED
Hereby, CDVI Wireless Spa, declares that the radio equipment type
,
is in compliance with directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address: www.erone.com.
SEL2641R433-TW
S2TR2641TW
