manualshive.com logo in svg

ERMA 2000iN, Руководство пользователя

Поделиться
Скачать
ERMA 2000iN Скачать руководство пользователя страница 5

 

 

1

1

、

Introduction                                                          

 

Your new ERMA product will more than satisfy your expectations. It has been manufactured under stringent ERMA Quality 
Standards to meet superior performance criteria. You will find your new ERMA item easy and safe to operate, and, with 
proper care, it will give you many years of dependable service. CAUTION. Carefully read through this entire Instruction 
Manual before using your new ERMA product. Take special care to heed the Cautions and Warnings. Your ERMA product 
has many features that will make your job faster and easier. Safety, performance, and dependability have been given top 
priority in the development of product, making it easy to maintain and operate. 

2

、

Environmental protection                                                                                       

 

   

Recycle unwanted materials instead of disposing of them as waste. All tools, hoses and packaging should 
be sorted, taken to the local recycling center and disposed of in an environmentally safe way.

 

 

3

、

Scope of product                                                       

This product is suited for home and camping applications. It will allow you to run equipment like outdoor lights, 
computers, sound systems, televisions, DVD and Video players, microwaves and allows you to recharge your car 
battery. When in use it is highly recommended to have a surge protector connected to the generator at all times. 

4

、

Description of symbols                                                                 

The rating plate on your tool may show symbols. These represent important information about the Product or 
instructions on its use.

 

   

 

 

 
 

Wear hearing protection.   

Wear eye protection. 

Wear breathing protection.

 

Содержание 2000iN













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды