manualshive.com logo in svg

ERMA 2000iN, Руководство пользователя

Поделиться
Скачать
ERMA 2000iN Скачать руководство пользователя страница 35

 

 

31

26

、

Spark plugs                                                                                             

                   

1. Remove spark plug maintenance cover (11) from the generator housing (FigT).   

 
 
 
 
 
 
 
 

2. Remove the spark plug lead (Fig.U). 

3. Remove any dirt from around the spark plug base. 

4. With the spark plug wrench provided remove the spark plug (Fig.V). 

5. Visually inspect the spark plug. Remove carbon deposits using a wire brush. 

6. Check for discoloration on the top of the spark plug. The standard colour should be a tan colour. 

7. Check the spark plug gap. The acceptable gap should be between 0.6–0.7mm(Fig.W). 

8. Install/reinstall the spark plug carefully by hand.   

9. Once the spark pug has been seated tighten with the spark plug wrench. 

10. Reinstall the spark plug cap on top of the spark plug. 

11. Reinstall the spark plug maintenance cover (11), and Reinstall handle. 

The recommended spark plugs are as follows: NGK CR7HSA 

 
 
 
 

 

T 

U 

V 

 

W 

Содержание 2000iN













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды