Ericsson HBS2 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 8

Ericsson HBS2 Скачать руководство пользователя страница 6

6

Registering a mobile phone to the HBS2 – Pairing

In order to make the first call through the HBS2, the mobile phone has to be
registered to the HBS2 – the so-called pairing or bonding.
After a reset i.e. activation of the Reset button, it is necessary to redo the pairing.
The mobile phone must be Bluetooth enabled.

Please refer to instructions regarding “Bluetooth wireless” in the user’s
guide of the actual mobile phone in use.

Pairing can take place in two cases. 1) Member pairing: a permanent pairing to the
HBS2 access point in the premises where the Mobile@Home solution is installed.
2) Guest pairing: a temporary pairing of a mobile phone to the HBS2 access point
e.g. during a visit in a premises of another owner (“Member”). Guest pairing infor-
mation is removed from the pairing list after 24 hours.

Member pairing

Prepare the HBS2 for Member pairing by pushing the button (Pairing button) on
the rear panel of the HBS2 once; see

Figure 6

.

The

Member

LED will flash fast green.

or

Guest pairing

Prepare the HBS2 for Guest pairing by double pushing the button (Pairing button)
on the rear panel of the HBS2; see

Figure 6

.

The

Guest

LED will flash fast green. Guest pairing is pairing a mobile phone when

visiting “another” home with an HBS2 access point (AP).

Figure 6 Press the Pairing button once for Member pairing

and twice for Guest pairing

«
...
4
5
6
7
8
»

Содержание HBS2









Отзывы:

Нет отзывов