background image

17 

 

2. 

I will have completed a successful radio equipment ground-range check before the first flight of a new or repaired model 
aircraft. 

3. 

I will not fly my model aircraft in the presence of spectators until I become a proficient flier, unless I am assisted by an 
experienced pilot. 

4. 

At all flying sites a line must be established, in front of which all flying takes place. Only personnel associated with flying 
the model aircraft are allowed at or in front of the line. In the case of airshows demonstrations straight line must be 
established. An area away from the line must be maintained for spectators. Intentional flying behind the line is prohibited. 

5. 

I will operate my model aircraft using only radio-control frequencies currently allowed by the Federal Communications 
Commission (FCC). Only individuals properly licensed by the FCC are authorized to operate equipment on Amateur Band 
frequencies. 

6. 

I will not knowingly operate my model aircraft within three (3) miles of any preexisting flying site without a frequency-
management agreement. A frequency management agreement may be an  
allocation of frequencies for each site, a day-use agreement between sites, or testing which determines that no 
interference exists. A frequency-management agreement may exist between two or more AMA chartered clubs, AMA 
clubs and individual AMA members, or individual AMA members. Frequency-management agreements, including an 
interference test report if the agreement indicates no interference exists, will be signed by all parties and copies provided 
to AMA Headquarters. 

7. 

With the exception of events flown under official AMA rules, no powered model may be flown outdoors closer than 25 feet 
to any individual, except for the pilot and located at the flightline. 

8. 

Under no circumstances may a pilot or other person touch a model aircraft in flight while it is still under power, except to 
divert it from striking an individual. 

9. 

Radio-controlled night flying is limited to low-performance model aircraft (less than 100 mph). The model aircraft must be 
equipped with a lighting system which clearly defines the aircraft's attitude and direction at all times. 

10.  The operator of a radio-controlled model aircraft shall control it during the entire flight, maintaining visual contact without 

enhancement other than by corrective lenses that are prescribed for the pilot. No model aircraft shall be equipped with 
devices which allow it to be flown to a selected location which is beyond the visual range of the pilot. 

 

WARNING – THIS IS NOT A TOY! 

Radio controlled model aircraft are capable of inflicting serious injury and/or property damage if 

not assembled, operated, and maintained in a competent and safe manner.  If you are not already experienced with radio controlled 

models, we strongly suggest that you find an experienced modeler to assist you. 

 

Warranty 

Hobby-Lobby guarantees this kit to be free from defects in both material and workmanship at the date of purchase.  This warranty 
does not cover any component parts damaged by use or modification.  In no event shall Hobby-Lobby’s liability exceed the original 

cost of the purchased kit. 

 

Completely read through this manual before starting construction. 

 

 

 

Hobby Lobby International, Inc. 

5614 Franklin Pike Circle 

Brentwood, TN 37027 

 

1-866-WE-FLY-RC 

(1-866-933-5972) 

 

www.hobby-lobby.com

 

 

Rev V1.2 on 3/11/10 
 

Corrected steps 44-45, 55-56 

Rev V1.3 on 3/12/10 
 

Corrected steps 38-43 

 

Содержание ERC1500 EUROFIGHTER


















Отзывы: