manualshive.com logo in svg

Erbauer ERB2151SE, Руководство пользователя

Поделиться
Скачать
Erbauer ERB2151SE Скачать руководство пользователя страница 6

6

ERBAUER 216MM (8”) SLIDING MITRE SAW

ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR MITRE SAW

ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR MITRE SAW

             

                 

Warning: Be sure to read and understand all instructions. Failure to 

         follow all instructions listed below may result in electric shock, fi re 
and/or serious personal injury.
1.    Know your power tool. Read operator’s manual carefully. Learn the 

applications and limitations, as well as the specifi c potential hazards 
related to this tool.

2.    Always wear safety glasses or eye shields when using this mitre saw. 

Everyday eyeglasses have only impact-resistant lenses; they are not 
safety glasses.

3.    Always protect your lungs. Wear a face mask or dust mask if the 

operation is dusty.

4.    Always protect your hearing. Wear hearing protection during extended 

periods of operation.

5.    Always inspect the tool cords periodically and if damaged have them 

repaired. Always be aware of the cord location.

6.    Always check for damaged parts. Before further use of the tool, 

aguard or other part that is damaged should be carefully checked to 
determine if it will operate properly and perform its intended function. 
Check for misalignment or binding of moving parts, breakage of parts, 
and any other condition that may affect the tool’s operation. A guard 
or other part that is damaged, should be properly repaired or replaced 
at an qualifi ed service centre.

7.    Do not abuse the cord. Never use the cord to carry the tools or pull 

the plug from the outlet. Keep cord away from heat, oil, sharp edges 
or moving parts. Replace damaged cords immediately. 

Damaged cords 

increase the risk of electric shock.

8.    Always make sure that your extension cord is in good condition. When 

using an extension cord be sure to use one that is heavy enough to 
carry the current that your tool will draw.

 

9.    Always inspect and remove all nails from lumber before sawing.
10. Do not use the tool while tired or under the infl uence of drugs, alcohol 

or any medication. 

Following this rule will reduce the risk of electric shock, fi re or 

serious personal injury.

11. Save these instructions. Refer to them frequently and use them to 

instruct others who may use this tool. If someone borrows this tool, 
make sure they have these instructions also.

        

Содержание ERB2151SE

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды