background image

● 

Overcharge of water. 

 

Tub seal (torn, worn or loose). 

Dishwasher door not sealing 

properly. 

Dishwasher is not level. 

Overburden (wrong type of 

detergent). 

Hose clamps loose. 

Heater element mounting nuts 

loose. 

Water seal leaking. 

O-ring is not in position. 

Motor and pump assembly not 

seated proper in tub liner bottom. 

Check and correct for proper 

fill. 

Replace tub seal. 

Adjust door latch assembly 

and/or strike. 

Level dishwasher properly. 

Instructs customer/user. 

 

Tighten all clamps securely. 

Tighten the nut. 

 

Use a new water seal. 

Adjust the ring or replace a new.

Replace seal. 

Poor wash ability. 

Spray arm not rotating. 

Improper loading of dishes, pans 

and other. 

 

Detergent dispenser inoperative. 

Insufficient amount of detergent. 

Or the detergent is old. 

Damaged or the impeller is broken.

Detergent  not dissolve. 

Check for proper rotation. 

Instructs customer/user on 

proper loading   per  owner’s 

guide. 

Repair or replace dispenser. 

On proper amount of fresh deter 

gent to use.   

Replace pump assembly. 

Incoming water temperature  of 

140

°

F  is required to proper 

dissolve detergent. 

Poor drying of dishes 

Improper loading of dishes, pots 

and other. 

Heating element (open). 

Incoming water temperature too 

low. 

Wiring or terminal (broken or 

burnt). 

Instruct customer/user on 

proper loading per owner’ s guide. 

Replace heating element. 

Incoming water temperature of 

140

°

F for best drying results. 

Replace or repair. 

Detergent cup will not open. 

Cup binding.   

Roll pin retainer or shaft broken. 

Defective bi-metal. 

Timer contact (open or broken). 

Repair or replace. 

Replace pin, retainer or shaft. 

Repair or replace. 

Replace timer. 

Door will not lath. 

Door latch damaged. 

Replace door latch. 

Rinse agent liquid will not 

eject. 

Electromagnetic valve defective. 

Rinse agent dispenser not mounted 

correctly. 

Plunger stuck or held in closed 

position. 

Replace valve. 

Mount securely to rear of inner 

door panel. 

Free plunger or adjust plunger 

release. 

Rinse agent liquid leaks. 

Container cracker or broken. 

Replace container. 

 12

Содержание SB 818














Отзывы: