Epson TM-T20II Скачать руководство пользователя страница 92

Страница: 92 / 140

XON/XOFF

Whe

XON/XOFF co

rol

s selec

ed,

he pr

int

he XON or XOFF s

ign

als as follows.

The

ing

of XON/XOFF d

ffers, depe

ing

he se

tting

he memory sw

ch.

Code

The hexadec

mal

mbers correspo

ing

he XON/XOFF codes are show

below.

• XON code: 11H

• XOFF code: 13H

Ethernet Interface

For

forma

abo

he e

her

int

erface, see

he UB-E03 Tech

cal Refere

ce G

de.

Signal

Printer status

Memory switch 1-3

1 (ON)

0 (OFF)

XON

1) When the printer goes online after turning on the power

Transmit

2) When the receive buffer is released from the buffer full state

Transmit

3) When the printer switches from offline to online

—

Transmit

4) When the printer recovers from an error using some ESC/POS

commands

—

Transmit

XOFF

5) When the receive buffer becomes full

Transmit

6) When the printer switches from online to offline

—

Transmit



When the printer goes from offline to online and the receive buffer is full, XON is not
transmitted.



When the printer goes from online to offline and the receive buffer is full, XOFF is not
transmitted.

Содержание TM-T20II













































































































































Результаты поиска

Содержание TM-T20II

Отзывы:

Похожие инструкции для TM-T20II

Бренды по названию

Популярные бренды

Epson TM-T20II, Техническое справочное руководство

Результаты поиска

Содержание TM-T20II

Отзывы:

Похожие инструкции для TM-T20II

Бренды по названию

Популярные бренды