Epson Stylus Pro 9700 Series Скачать руководство пользователя страница 177

Страница: 177 / 228

177

Solving Problems

177

CLEANING ERROR

AUTOMATIC HEAD
CLEANING FAILED
RETRY?
YES
NO

Head cleaning did not clear the
nozzles.

Press

to clear the error and run the

head cleaning utility again. If cleaning
doesn’t start, cancel printing from the
computer. Then turn the printer off and back
on again.

CLEANING ERROR
NOT ENOUGH INK.
CONTINUE CLEANING?
YES (RECOMMENDED)
NO

There is not enough ink to
perform cleaning.

Select

Yes

and replace the cartridge (see

page 157).

CLEANING ERROR
NOT ENOUGH EMPTY
SPACE IN MAINT TANK.
CONTINUE CLEANING?
YES (RECOMMENDED)
NO

There is not enough space in
the maintenance tank to
perform cleaning.

Select

Yes

and replace the maintenance

tank (see page 166).

COMMAND ERROR

CHECK DRIVER SETTINGS

You may be using the wrong
printer driver.

Damaged data was sent to the
printer or the data has an
incorrect command.

Press

to cancel the print job and reset

the printer. Make sure you installed the
correct driver for your printer.

CUTTER UNIT NEARING
END OF SERVICE LIFE.
RECOMMEND REPLACING
THE CUTTER UNIT

The paper cutter may be dull.

Replace the paper cutter; see page 162.

FRONT COVER OPEN

CLOSE FRONT COVER

Front cover is open.

Close the front cover.

F/W INSTALL ERROR

UPDATE FAILED RESTART
THE PRINTER

Firmware update failed.

Restart the printer, then update the
firmware again; see page 55.

INK CARTRIDGE

INK LOW REPLACE INK
CARTRIDGE

The ink cartridge is expended.

Replace the ink cartridge; see page 157.

Message

Explanation

Response

Содержание Stylus Pro 9700 Series





































































































































































































































Результаты поиска

Содержание Stylus Pro 9700 Series

Отзывы:

Похожие инструкции для Stylus Pro 9700 Series

Бренды по названию

Популярные бренды

Epson Stylus Pro 9700 Series, Руководство пользователя

Результаты поиска

Содержание Stylus Pro 9700 Series

Отзывы:

Похожие инструкции для Stylus Pro 9700 Series

Бренды по названию

Популярные бренды