Epson Stylus 1500 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 185

background image

Disassembly and Assembly

This section describes procedures for disassembling the printer’s main components. Unless
otherwise specified, you can reassemble disassembled units or components by reversing
disassembly procedures. Therefore, no assembly procedures are included. Precautions for any
disassembly or assembly procedure are described under Disassembly/Assembly Points. Adjustments
required after assembling the unit are described under Required Adjustments.

Precautions for Disassembling the Printer

Follow the precautions below when disassembling the printer.

WARNING

❒

Disconnect the power cable before disassembling or assembling the printer.

❒

Wear protective goggles to protect your eyes from ink. If ink gets in your eye, flush it
with fresh water and see a doctor immediately. If ink comes into contact with your skin,
wash it off with soap and water. If irritation occurs, contact a physician.

❒

A lithium battery is installed on the C172 MAIN board of this printer. Be sure to observe
the following instructions when servicing the battery:
1. Keep the battery away from any metal or other batteries so that electrodes of opposite

polarities do not come in contact with each other.

2. Do not heat the battery or place it near fire.
3. Do not solder any part of the battery. (Doing so may result in leakage of electrolyte

from the battery, burning, or explosion. The leakage may affect other devices close
to the battery.)

4. Do not charge the battery. (An explosive gas may be generated inside the battery,

and cause burning or explosion.)

5. Do not dismantle the battery. (The gas inside the battery may hurt your throat.

Leakage, burning, or explosion may also result.)

6. Do not install the battery in the wrong direction. (This may cause burning or

explosion.)

❒

Never touch the primary parts of the power supply unit (including the heat sink) while
plugging it in.

CAUTION

There is danger of explosion if the battery is replaced incorrectly. Replace it only with the
same or equivalent type, recommended by the manufacturer. Dispose of used batteries
according to government’s laws and regulations.

Only remove the ink supply tube when necessary. If you need to disconnect it, be sure to
raise the end of the tube to prevent the ink from leaking out.

ATTENTION

Risque d’explosion si la pile est remplacée incorrectement. Ne remplacer que par une pile
du même type ou d’un type équivalent recommandé par le fabricant. Elminer les piles
déchargées selon les lois et les règles de sécurité en vigueur.

EPSON Stylus 1500 Service Manual

3-3

«
...
70
71
72
73
74
...
»

Содержание Stylus 1500


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Stylus 1500

imagePROGRAF W8400

Бренд: Canon Страницы: 24

Super G3 FAX Board-T1

Бренд: Canon Страницы: 16

imagePROGRAF TZ-30000

Бренд: Canon Страницы: 66

imagePROGRAF W7200

Бренд: Canon Страницы: 126

imagePROGRAFi iPF840 series

Бренд: Canon Страницы: 149

Бренд: Canon Страницы: 166

iP4000 - PIXMA Photo Printer

Бренд: Canon Страницы: 2

iP4000 - PIXMA Photo Printer

Бренд: Canon Страницы: 3

Бренд: Canon Страницы: 21

Бренд: Olympus Страницы: 3

BW Remote Operators Software Kit-A1

Бренд: Canon Страницы: 20

imageRUNNER 2420

Бренд: Canon Страницы: 30

Бренд: Canon Страницы: 51

imageCLASS LBP325dn

Бренд: Canon Страницы: 252

Бренд: Octave Страницы: 2

Бренд: GCC Technologies Страницы: 63

Бренд: gCreate Страницы: 9

Бренд: GCC Technologies Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды