Epson Stylus 1500 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 185

background image

PRECAUTIONS

Precautionary notations throughout the text are categorized relative to

1. personal injury
2. damage to equipment.

WARNING

Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be
exercised in performing procedures preceded by a WARNING heading.

CAUTION

Signals a precaution which, if ignored, could result in damage to equipment.

Always observe the precautionary measures itemized below when performing repair/maintenance procedures.

WARNING

1.

Always disconnect the product from both the power source and host computer before performing any
maintenance or repair procedure.

2.

No work should be performed on the unit by persons unfamiliar with basic safety measures dictated for all
electronics technicians in their line of work.

3.

In performing testing described in this manual, do not connect the unit to a power source until instructed to
do so. When the power supply cable must be connected, use extreme caution in working on the power supply
and other electronic components.

CAUTION

1.

Repairs on EPSON products should be performed only by an EPSON-certified repair technician.

2.

Make certain that the source voltage is the same as the rated voltage listed on the serial number/rating plate.
If the EPSON product has a primary AC rating different from the available power source, do not connect it to
the power source.

3.

Always verify that the EPSON product has been disconnected from the power source before removing or
replacing printed circuit boards and/or individual chips.

4.

To protect sensitive

µ

P chip and circuitry, use static discharge equipment, such as anti-static wrist straps,

when accessing internal components.

5.

Replace malfunctioning components only with those components recommended by the manufacturer;
introduction of second-source ICs or other nonapproved components may damage the product and void any
applicable EPSON warranty.

iv

EPSON Stylus 1500 Service Manual

«
...
3
4
5
6
7
...
»

Содержание Stylus 1500


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Stylus 1500

Panafax UF-7000

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 120

Бренд: Panasonic Страницы: 100

KX-MB781 - B/W Laser - All-in-One

Бренд: Panasonic Страницы: 96

Бренд: Panasonic Страницы: 130

Бренд: Oki Страницы: 210

Бренд: Panasonic Страницы: 77

Бренд: Panasonic Страницы: 402

Бренд: Panasonic Страницы: 54

Workio DP-8016P

Бренд: Panasonic Страницы: 88

Бренд: Panasonic Страницы: 60

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 341

Бренд: Samsung Страницы: 8

CLX2160N - Color Laser - All-in-One

Бренд: Samsung Страницы: 118

CLX 3160FN - Color Laser - All-in-One

Бренд: Samsung Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды