Epson SC-F9300 series Скачать руководство пользователя страница 61

Страница: 61 / 146

Put the cup supplied with the ink cleaner on
the metal tray, and pour approximately 10 ml
of ink cleaner into the cup.

Dampen the cleaning stick with ink cleaner.

Do not allow ink cleaner to drip from the
cleaning stick.

When dampening a clean-room wiper with ink
cleaner, use ink cleaner poured into a cup.

Important:

❏

Do not use ink cleaner that you have
used for cleaning to clean the next time.
Using dirty ink cleaner will make
staining worse.

❏

Tightly close the lid of the ink cleaner
and store it at room temperature out of
direct sunlight and away from high
temperatures or humidity.

❏

Used ink cleaner, cleaning stick, and
clean-room wipers are industrial waste.
Dispose of them in the same way as for
waste inks.

“Disposal of used consumables” on

page 80

Moving the Print Head

This section describes how to move to cleaning
position of the print head.

Important:

Be sure to follow the steps below when positioning
the print head. Moving the print head manually
could cause malfunction.

Buttons that are used in the following settings

Confirm that the status screen shown below is
displayed, and then press the

button.

The Maintenance menu will be displayed.

Use the

buttons to select

Head

Maintenance

and press the

button.

Press the

buttons to select

Regular

Cleaning

, and then press the

button two

times.

The print head moves to the cleaning position.

SC-F9300 Series User's Guide

Maintenance

Содержание SC-F9300 series



















































































































































Результаты поиска

Содержание SC-F9300 series

Отзывы:

Похожие инструкции для SC-F9300 series

Бренды по названию

Популярные бренды

Epson SC-F9300 series, Руководство пользователя

Результаты поиска

Содержание SC-F9300 series

Отзывы:

Похожие инструкции для SC-F9300 series

Бренды по названию

Популярные бренды