Epson S1R72104 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 65

Epson S1R72104 Скачать руководство пользователя страница 24

S1R72104 Technical Manual

Rev.1.1

EPSON

19

* Operational settings of the port interface
Shown below is a list of the operational settings made by the bit setting.

1) Switching master/slave of the port by PSLV bit

PDREQ

XPDACK

XPRD/XPWR

Remarks

PSLV=0
(Master)

Input

Output

Output

Data input during XPRD
Data output during XPWR
Setting of STB3 to 0 valid
XPRD/XPWR pulse width:

Assert

≥

40ns

Negate

≥

40ns

PSLV=1
(Slave)

Output

Input

Input

Data output during XPRD
Data input during XPWR
Setting of STB3 to 0 invalid
XPRD/XPWR pulse width:

Assert

≥

30ns

Negate

≥

30ns

2) Switching operational modes by BUS8/SWAP/ODS bit

BUS8=0 SWAP=0

PD7 to 0 is transferred to and from SCSI block first.
If ODS = 1, PD7 to 0 is discarded when the first one word is transferred,
and only PD15 to 8 is transferred.
PD7 to 0 is used if the last data to be transferred is not a word but a byte.

SWAP=1

PD15 to 8 is transferred to and from SCSI block first.
If ODS = 1, PD15 to 8 is discarded when the first one word is transferred,
and only PD7 to 0 is transferred.
PD15 to 8 is used if the last data to be transferred is not a word but a byte.

BUS8=1

Only PD7-0 is used for transfer.
PD15 to 8 is used for Input mode (connect to GND).

7.3.22 CONFIG1 (CONFIG1) R/W

Sets the operational mode of the IC.

7 6 5 4 3 2 1 0

NP3

NP2 NP1 NP0 AP3

AP2 AP1 AP0

1Dh

BIT7 to 4 NP3 to 0

Sets the negate pulse width of XPRD/XPWR when the port operates in Master mode.
The width is the internal operation clock cycle (40MHz) multiplied by [(NP3 to 0)+2].
ex 0000: 2

×

25ns=50ns

0001: 3

×

25ns=75ns

BIT3 to 0 AP3 to 0

Sets the assert pulse width of XPRD/XPWR when the port operates in Master mode.
The width is the internal operation clock cycle (40MHz) multiplied by [(AP3 to 0)+2].
ex 0000: 2

×

25ns

＝

50ns

0001: 3

×

25ns

＝

75ns

«
...
22
23
24
25
26
...
»

Содержание S1R72104


































































Отзывы:

Нет отзывов