Epson S1C17M12 Скачать руководство пользователя

Страница: 99 / 253

11 UART (UART3)

S1C17M12/M13 TECHNICAL MANUAL

Seiko Epson Corporation

11-3

(Rev. 1.2)

11.3.2 Clock Supply in SLEEP Mode

When using the UART3 during SLEEP mode, the UART3 operating clock CLK_UART3_

must be configured so

that it will keep supplying by writing 0 to the CLGOSC.

xxxx

SLPC bit for the CLK_UART3_

clock source.

11.3.3 Clock Supply in DEBUG Mode

The CLK_UART3_

supply during DEBUG mode should be controlled using the UA

CLK.DBRUN bit.

The CLK_UART3_

supply to the UART3 Ch.

is suspended when the CPU enters DEBUG mode if the UA

CLK.DBRUN bit = 0. After the CPU returns to normal mode, the CLK_UART3_

supply resumes. Although the

UART3 Ch.

stops operating when the CLK_UART3_

supply is suspended, the output pin and registers retain the

status before DEBUG mode was entered. If the UA

CLK.DBRUN bit = 1, the CLK_UART3_

supply is not sus-

pended and the UART3 Ch.

will keep operating in DEBUG mode.

11.3.4 Baud Rate Generator

The UART3 includes a baud rate generator to generate the transfer (sampling) clock. The transfer rate is determined

by the UA

MOD.BRDIV, UA

BR.BRT[7:0], and UA

BR.FMD[3:0] bit settings. Use the following equations to

calculate the setting values for obtaining the desired transfer rate.

CLK_UART2 CLK_UART2

bps = ———————————

BRT = BRDIV

(

————————— - FMD

)

- 1 (Eq. 11.1)

BRT + 1

bps

————— + FMD

BRDIV

Where

bps:

Transfer rate [bit/s]

CLK_UART3: UART3 operating clock frequency [Hz]

BRDIV:

Baud rate division ratio (1/16 or 1/4)

Selected by the UA

MOD.BRDIV bit

BRT: UA

BR.BRT[7:0] setting value (0 to 255)

FMD: UA

BR.FMD[3:0] setting value (0 to 15)

For the transfer rate range configurable in the UART3, refer to “UART Characteristics, Transfer baud rates U

BRT1

and U

BRT2

” in the “Electrical Characteristics” chapter.

11.4 Data Format

The UART3 allows setting of the data length, stop bit length, and parity function. The start bit length is fixed at one

bit.

Data length

With the UA

MOD.CHLN bit, the data length can be set to seven bits (UA

MOD.CHLN bit = 0) or eight bits

(UA

MOD.CHLN bit = 1).

Stop bit length

With the UA

MOD.STPB bit, the stop bit length can be set to one bit (UA

MOD.STPB bit = 0) or two bits

(UA

MOD.STPB bit = 1).

Parity function

The parity function is configured using the UA

MOD.PREN and UA

MOD.PRMD bits.

Table 11.4.1 Parity Function Setting

UAnMOD.PREN bit

UAnMOD.PRMD bit

Parity function

Odd parity

Even parity

Non parity

Содержание S1C17M12






























































































































































































































































Результаты поиска

Содержание S1C17M12

Отзывы:

Похожие инструкции для S1C17M12

Бренды по названию

Популярные бренды

Epson S1C17M12, Техническое руководство

Результаты поиска

Содержание S1C17M12

Отзывы:

Похожие инструкции для S1C17M12

Бренды по названию

Популярные бренды