Epson Priority Fax 2000 Скачать руководство пользователя страница 96

Страница: 96 / 112

Troubleshooting

Telephone
(continued)

The telephone does not ring.

The ringer switch is off. Turn the ringer switch to H for high
or L for low.

When you press SPKR you hear nothing.

Check to be sure the power cord is plugged in.

Check the speaker volume dial on

the

back control panel. If it is

set to the minimum, turn the volume higher.

LCD Error Messages

You may receive the following error messages on the LCD display.

You are out of recording paper. Load a new roll according to

the instructions in Chapter 1.

The recording paper may not be inserted properly. See
Chapter 1.

Documents may

not

have been fed correctly Resend the

documents (up to five pages at a time).

You may be using an incorrect procedure for sending a

document. See Chapter 2 and try sending the document again.

If you are receiving a document, the sending party may be
having a problem during transmission. Call the sender.

You may be attempting to transmit to a non-fax number. Check
to make sure the number you are calling is a fax number, then

try sending the document again.

If you are sending a document and the transmission is not
successful, this message is displayed. Press

STOP

and try

sending the document again.

Содержание Priority Fax 2000

















































































































Результаты поиска

Содержание Priority Fax 2000

Отзывы:

Похожие инструкции для Priority Fax 2000

Бренды по названию

Популярные бренды

Epson Priority Fax 2000, Руководство пользователя

Результаты поиска

Содержание Priority Fax 2000

Отзывы:

Похожие инструкции для Priority Fax 2000

Бренды по названию

Популярные бренды