Epson PERFECTION V10 Скачать руководство пользователя страница 43

Страница: 43 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of TPU

4.4 Disassembly of TPU

4.4.1 TPU Upper Housing

1. Disengage the Hinge.

(4.3.1 Hinge Disengagement on page 34)

2. Slide the TPU Housing Mat in the direction of the arrow, releasing it from the

sockets of the TPU Unit and remove it.

Figure 4-24. Removing the Housing Mat

3. Remove the four screws (C.B.P 3x8, 5-7 kgf.) that secure the TPU Upper Housing.

Figure 4-25. Removing the TPU Upper Housing (1)

4. Using a flat-blade screwdriver, push outward on the left and right sides of the TPU

Upper Housing frame to widen it and release the two Hook A.

5. Disengage the two Hook B by pinching them.

6. Slide the TPU Lower Housing in the direction of the arrow, then release the four

Hook C, and remove the TPU Upper Housing.

Figure 4-26. Removing the TPU Upper Housing (2)

Socket

TPU Housing Mat

TPU Unit

C.B.P. 3x8

TPU Upper

Housing

Hook A
Hook B
Hook C

TPU Upper Housing

TPU Lower Housing

Содержание PERFECTION V10














































































Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды

Epson PERFECTION V10, Руководство по обслуживанию

Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды