background image

1

Safety Instructions

Important safety instructions

Read all of these instructions and save them for 
later reference. Follow all warnings and 
instructions marked on the unit.

Do not place the unit near a radiator or heat 
source.

Unplug the printer before cleaning. Clean 
with a damp cloth only. Do not spill liquid on 
the unit.

Except as specifically explained in this guide, 
do not attempt to service the unit yourself.

Unplug the unit and refer servicing to 
qualified service personnel under the 
following conditions:

if liquid has entered the unit;

if the unit has been dropped or the cabinet 
damaged;

if the unit does not operate normally or 
exhibits a distinct change in performance. 

Note:

Adjust only those controls that are covered by the 
operating instructions.

A few precautions

Always turn the printer off before changing 
the roll paper. Accidental operation of the 
take-up motor can cause injury.

Make sure that the take-up reel unit is securely 
locked into place. Incorrect installation can 
cause the roll to fall and cause injury.

Do not touch the auto take-up reel unit while 
it is operating. Hair or clothing can become 
caught in the unit and cause injury.

Do not look directly at the sensor beam. Doing 
so may cause permanent eye damage.

For United Kingdom users

Use of options

Epson (UK) Limited shall not be liable against any 
damages or problems arising from the use of any 
options or consumable products other than those 
designated as Original EPSON products or 
EPSON Approved products by Epson (UK) 
Limited.

Warnings, cautions, and notes

 

w

Warnings 

must be followed carefully to avoid 

bodily injury.

 

c

Cautions 

must be observed to avoid damage to 

your equipment.

Notes 

contain important information and useful tips 

on the operation of the product.

English

Содержание P260













Отзывы: