Epson Equity 386/20 Скачать руководство пользователя страница 42

Страница: 42 / 45

PSB No: S-0047C
Page: 3 of 6

Q6.

Q7.

Q8.

Q9.

What memory expansion boards are compatible with the Equity I and

Equity II?

The following boards have been tested by Epson in the Equity I and

II:

All Card w/MMU Multifunction All Computers,

Inc.

Liberty PC

Quadram Corporation

Mini Magiccard (EV - 138)

Everex Systems, Inc.

AST SixPak Premium

AST Research

AST Rampage

AST Research

What memory expansion boards are compatible with the Equity Ill?

The following boards have been tested by Epson in the Equity Ill:

Grande Byte

STB Systems

Intel Above Board AT

Intel Corporation

Liberty AT

Quadram Corporation

AST Advantage

AST Research

AST Rampage AT

AST Research

AST Ramvantage

AST Research

What memory expansion boards are compatible with the Equity I +?

The following boards have been tested by Epson in the Equity I +:

64/256KB Expansion Option
Above Board PC (1985)

Fastcard IV (1.6)

IBM
Intel Corporation

Thesys

What memory expansion boards are compatible with the Equity le?

The following boards have been tested by Epson in the Equity le:

64/256KB Expansion Option

IBM

Quad Board II

Quadram

Fastcard IV

Thesys

RAMpage

AST Research

Note: The Intel Above Boards do not currently operate reliably with

the Equity le.

Содержание Equity 386/20














































Результаты поиска

Содержание Equity 386/20

Отзывы:

Похожие инструкции для Equity 386/20

Бренды по названию

Популярные бренды

Epson Equity 386/20, Информационный бюллетень по поддержке продукции

Результаты поиска

Содержание Equity 386/20

Отзывы:

Похожие инструкции для Equity 386/20

Бренды по названию

Популярные бренды