Epson Stylus SX230 series / SX235W series / SX430W series / SX440W series
Revision B
Adjustment
Required Adjustments
45
Confidential
Par
t Na
me
LD Roller
Assy
Remove
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Replace
---
---
---
---
---
---
---
---
O
---
---
---
---
---
---
---
---
CR Motor
Remove
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Replace
---
---
---
---
---
---
---
---
---
---
---
---
---
---
O
---
---
PE Sensor
Lever
Remove
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Replace
---
---
---
---
---
---
---
---
O
---
---
---
---
---
---
---
---
Main Board
Remove
---
---
---
---
---
---
---
---
O
---
---
---
---
---
---
---
---
Replace
(Read OK)
---
---
O
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Replace
(Read NG)
---
---
---
O
O
---
O
*2
O
O
O
O
O
O
O
O
O
---
CR Driven
Pulley
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
O
*4
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Main Frame
Assy
Remove
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Replace
O
O
*4
---
---
---
---
---
O
---
O
O
O
O
---
---
---
---
Table 3-1. Required Adjustment List
Adjustment Type
Mechanism adjustment
Adjustment using the Adjustment Program
Priority
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Adjustment Item
Checking the
Platen Gap
CR/PF Belt
tension check
EEPROM
data copy
Initialize Setting
Head ID input
Ink charge
Maintenance
counter
First dot
position
adjustment
TOP margin
adjustment
Head angular
adjustment
Bi-D adjustment PF adjustment
PF band
adjustment
PF deterioration
offset
CR motor heat
protection
control
PF motor heat
protection
control
Scanner motor
heat protection
control
Purpose
Check if the PG is
within the
standard.
Check the tension
of the CR Timing
Belt and PF
Timing Belt.
To copy
adjustment values
or the like stored
on the old Main
Board to the new
board when the
Main Board needs
to be replaced.
To write sale-
destination-specific
settings and the
serial number into
the Main Board
after replacing it.
And also to set the
MAC address as
necessary.
To correct
characteristic
variation of the
replaced
Printhead by
entering its
Printhead ID
(Head ID).
To fill ink inside
the new Printhead
to make it ready
for print after
replacing the
Printhead.
To reset the waste
ink counter after
replacing the
Waste Ink Pad
Assy.
To correct the
print start position
in the CR Unit
moving direction
through software
control.
This corrects top
margin of printout.
To correct tilt of
the Printhead
caused at the
installation
through software
control.
To correct print
start timing in
bidirectional
printing through
software control.
To correct
variations in paper
feed accuracy to
achieve higher
print quality.
To correct
variations in paper
feed accuracy to
achieve higher
print quality in
band printing.
To reset the
counter or set it to
its maximum
according to the
replaced parts.
To measure and
correct the
electrical
variation of the
motor and the
power supply
board.
To measure and
correct the
electrical
variation of the
motor and the
power supply
board.
To measure and
correct the
electrical
variation of the
motor.
Printout pattern
---
---
---
---
---
---
---
---
---
---
---
How to judge
See
“ 3.3.1
Checking the
Platen Gap (p49)”
for the details.
See
“ 3.3.2 CR/PF
Belt Tension
Check (p50)”
for
the details.
---
---
---
---
---
Examine the
misaligned lines
printed on the left
side of the paper,
and enter the
number beside the
line that is exactly
5 mm away from
the paper edge.
Examine the
misaligned lines
printed on top of
the paper, and
enter the number
beside the line
that is exactly 5
mm away from
the paper edge.
Enter the values
of the most
straight lines.
Examine the
printout patterns
for each of the
four modes, and
enter the value for
the pattern with
no gap and
overlap for each
mode.
Normal area
pattern
Examine the
printout patterns
and enter the
value for the
pattern with
fewest lines.
Bottom area
pattern
Examine the
printout patterns
and enter the
value for the
pattern with no
overlap and gap
between the two
rectangles.
Examine the
printout patterns
and enter the
value for the
pattern with no
overlap and gap
between the two
rectangles.
---
See
“ 3.2.2.1 CR
Motor Heat
Protection Control
/ PF Motor Heat
Protection Control
(p47)”
for the
details.
See
“ 3.2.2.1 CR
Motor Heat
Protection Control
/ PF Motor Heat
Protection Control
(p47)”
for the
details.
See
“ 3.2.3
Scanner Motor
Heat Protection
Control (p48)”
for
the details.
Adjustment program
---
---
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Tool
See
p49
See
p50
---
---
---
---
---
Ruler
Ruler
---
---
---
---
---
---
---
---
Note "*1": Necessary when the part is replaced at a point in the disassembly procedures other than specified in this manual.
"*2": Replacement of the Paper Guide Lower Porous Pad and Waste Ink Pad Assy is necessary.
"*3": Perform PF Belt tension check only.
"*4": Perform CR Belt tension check only.
-2
-1
0
1
2
-
2
-1 0 1 2
NG
OK
OK
NG
NG
OK
NG
NG
OK
NG
NG
OK
NG
NG
Содержание Epson Stylus NX330
