Epson Elp-3500 Скачать руководство пользователя страница 89

Страница: 89 / 114

EPSON ELP-3500 Service Manual

5-4

***Flicker Adjustment***
COLOR RED
Change data using arrow key.
Left Arrow Key: down Right Arrow Key: up
Select Enter Key: set

Figure 5-4.

3. Use the arrow keys to increase or decrease the value by one. Find the display with

the minimum flicker.

When you press the left arrow key, an adjustment value from "0(00) to 64(40)"
appears in the lower left corner of the screen.

4. Press Enter, and a 16-level green-scale pattern should appear on the projector

screen.

5. Just as in step 3, find the display with the minimum flicker.

6. Press Enter, and a 16-level blue-scale pattern should appear on the projector

screen.

7. Just as in step 3, find the display state with the minimum flicker.

2. Ghost Adjustment

1. Type

2 from the main menu to eliminate ghosts.

2. Make sure the projector displays the 16-level red-scale pattern section at the top of

the screen. (Dark patterns appear on the left side; brighter patterns on the right side.)

Содержание Elp-3500



















































































































Результаты поиска

Содержание Elp-3500

Отзывы:

Epson Elp-3500, Руководство по обслуживанию, Страница: 89 / 114

Результаты поиска

Содержание Elp-3500

Отзывы: