Epson Elp-3500 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 114

Epson Elp-3500 Скачать руководство пользователя страница 87

EPSON ELP-3500 Service Manual

5-2

After completing the focus alignment, you should use the image adjustment program to
obtain the best display quality. This program specify the electrical parameters in order to
obtain best display quality.

5.1.2 Running the Program

The image adjustment program is supplied on an MS-DOS diskette. Follow the
messages in the image adjustment program as you select menu options.

When menu options 1 through 4 are executed, the image adjustment program transfers
the adjusted settings to the projector’s RAM via the RS-232C interface. Unless you save
these settings, they are lost and invalid when the projector is restarted. Therefore, once
you make adjustments in the image adjustment program, choose menu option 5, "Data
Transfer," to program settings into the projector’s flash ROM.

* Do not use menu option 6 (standard data transfer) unless specifically told to do so.

1.  Place the screen about 8 feet (2.4 m) away from the projector.
2.  Turn on the projector and host computer.
3.  Adjust the focus ring on the projector so that the projected image on the screen is in

focus. Use the zoom ring to set the screen projection size to 60 inches.

Start-up Procedure

Windows 95 system

1. Insert the image adjustment program diskette into the diskette drive.

2. Select

the

My computer

from the initial computer display.

3.  Be sure the screen displays My computer. Then select the 3.5 inch FD(A:) icon.
4.  Make sure the screen displays an RS353AS folder, then select it.
5.  Make sure the screen displays a AS6 folder, then select it.
6.  Make sure the screen displays an RS353ASE.EXE file, then select it.

MS-DOS or Windows 3.1 system

1. Make sure the computer screen displays the C:\> prompt. If Windows 3.1 is

running, select the MS-DOS prompt from the Program Manager or exit Windows

and display the C:\> prompt. (If the C:\WINDOWS> prompt appears on the screen
instead of C:\>, type CD\ then press Enter.)

END

Choose menu

option 5 (Data

Transfer)

Choose menu

option 0; then 1 to 6

(Adjustments)

Start image

adjustment

program

Figure 5-2

«
...
85
86
87
88
89
...
»

Содержание Elp-3500



















































































































Отзывы:

Нет отзывов