Laser
Service Manual
. .
Table 1-13.
Parallel Interface Pin Assignment
No.
Signal Name
Description
STROBE is a strobe pulse used to read data from the host
STROBE
IN
computer. The pulse width must be more than 0.5
Normally it is HIGH, and data is latched at the
edge of
this signal.
DATA 1 to 8 are parallel data bits. When the signal is HIGH,
the data bit is 1, and when it is LOW, the data bit is O.
2-9
DATA 1-8
The most
bit
is DATA8. The
must be maintained for 0.5
on either side of the
STROBE signal active edge.
is an acknowledge pulse with an approximate width
of 10 @cc. This signal goes LOW when the data reception is
10
OUT
completed, which indicates that the printer can accept new
data. Timing with the BUSY signal is specified through
The BUSY signal informs the host computer of the printer
11
BUSY
OUT
state. When the signal is HIGH, the printer cannot
data.
The PE signal
paper empty for the standard
12
PE
OUT
cassette selected through
or command, or for the
option paper cassette. Paper empty is
by HIGH.
13
OUT
Pulled up to
through a 3.3
resistor.
If the AUTO FEED signal is set to LOW, the printer
performs a LF (line
upon
a CR
(Carriage Return) oode from the host computer.
In GQ Mode (option) or
Mode, AUTO-FEED signal
14
AUTO-FEED
IN
the CR operation according to
settings. In
HP Mode, AUTO-FEED signal is
ignored.
can only be done when the printer is ON or when active
is
to parallel interface.
This signal is detected only when the power is turned ON, or
when the printer is initialized.
15
NC
.
Not used.
16
GND
ground level.
17
CHASSIS GND
-
Connected to the printer chassis. The printer chassis
GND
and the signal GND are connected to each other.
18
NC
Not
1 9 - 3 0
GND
Ground level for the twisted pair return signal.
31
IN
The STROBE signal is ignored when this signal is LOW.
This level goes LOW when the printer is:
●
out of paper
32
ERROR
OUT
●
paper jam
●
in error state
●
off line
33
GND
Same as for pins19 to 30.
34
NC
Not
35
Pulled up to
through 3.3
resistance.
Rev.
1-15
Содержание ActionLaser 1000
