Epson 2000P - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Страница: 143 / 178

EPSON Stylus PHOTO 2000P Revision A
MAINTENANCE Overview 143
Table 6-2. Lubrication Point
Lubrication Point
Lubricant Type &
Amount
Refer to:
1 BUSHING, 12, RIGHT
• Using a brush, apply the grease
evenly to the inside surface of the
bushing.
G-26
A 3-mm wide bead
Page 144
2 HOLDER, PULLEY, DRIVEN G-26
φ
1 x 3mm (for each of
the 4 points)
Page 144
3 BUSHING, 12, LEFT
• Using a brush, apply the grease to
the inside surface of the bushing.
G-26
A 3-mm wide bead
Page 145
4 BUSHING, 6
• Using a brush, apply the grease to
the inside surface of the bushing.
G-26
A 1-mm wide bead
Page 145
5 PULLEY, DRIVEN
• Apply the grease to the flat surface.
G-26
φ
1 x 1mm (2 points)
Page 145
6 SHAFT, PULLEY, DRIVEN G-26
φ
1 x 1mm
Page 145
7 COMBINATION GEAR, 12, 22.4
• Using a dispenser, apply the oil to
the entire inside circumference of
the gear.
O-12 Page 145
8 COMBINATION GEAR, 14, 28
• Using a dispenser, apply the oil to
the entire inside circumference of
the gear.
O-12 Page 145
9 Pole C (2 points) G-26,
φ
1 x 3mm Page 145
10 PAD, D3.6 for COMBINATION GEAR
12, 22.4
• Wipe off any excess oil that comes
out toward the motor.
O-12
Dip the pad in the oil
to soak it.
Page 145
11 PAD, D3.6 for COMBINATION GEAR
14, 28
• Wipe off any excess oil that comes
out toward the motor.
O-12
Dip the pad in the oil
to soak it.
Page 145
12 Groove on “ROLLER, PF” G-26
φ
1 x 5mm
Page 146
13 Contact area for ROLLER, EJECT and
GROUND SPRING, EJECT G-26
φ
1 x 2mm
Page 146
14 Contact areas for ROLLER, PF and
PAPER GUIDE, REAR
• Apply the grease while rotating the
shaft.
NOTE: Do not get the grease on the
specially coated area of
ROLLER, PF.
G-26
φ
1 x 1/2 of the
circumference
Page 146
15 PAPER GUIDE, FRONT (3 points)
NOTE: Do not get the grease on the
rubber rollers of the Paper
Eject Roller.
G-26
•
φ
1 x 2mm
(Eject Roller side)
•
φ
1 x 10mm
(PF Roller side)
Page 146
16 Oil pad in the carriage assembly
• Lubricate the oil pad only when:
1) Replacing the carriage unit
2) Replacing the oil pad
• Use a dispenser to supply oil.
• After oiling to the pad, leave it for
one minute and then mount it to the
carriage unit with its oiled side
facing the CR guide shaft.
NOTE: If you supply too much
oil, throw away the pad
and start over with a new
one.
O-12
0.72 ~ 0.77cc (0.65 ~
0.69g)
Table 6-2. Lubrication Point (continued)
Lubrication Point
Lubricant Type &
Amount
Refer to: